Prob. 16.8 A clay layer of thickness 7 m after 1 year when it was consolidated to 40% settled by 13 cm. If for the same clay layer and similar loading conditions but the thickness is increased by 14 m. How much settlement would you expected for this new clay layer at the end of 3 years. Calculate your answer in "mm"

Prob. 16.8 A clay layer of thickness 7 m after 1 year when it was consolidated to 40% settled by 13 cm. If for the same clay layer and similar loading conditions but the thickness is increased by 14 m. How much settlement would you expected for this new clay layer at the end of 3 years. Calculate your answer in "mm"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ASAP. Answer is Given. Please show how to solve
As indicated in the following figure, an incompressible silty sand fill 16.4 ft thick wasplaced on top of a 49.2 ft thick layer of soft and compressible silty clay. Underlying theclay is a layer of incompressible sandy gravel. The soil properties of the silty clay layer aregiven in the following figure. The ultimate settlement, Sult = 5.64 ft, from the primaryconsolidation of silty clay layer due to the weight of the silty sand fill is calculated. A) Find the time rate of settlement by showing the Time [year] vs. Settlement [ft] curve.Show sample calculation when percentage of consolidation, Uavg = 50% B) Compute and plot effective stress profile (σ’z vs. depth) at the Silty Clay layer in thefollowing timing:a. Before placing the fill layerb. right after placing the fill layerc. Ten years after placing the fill layerd. 40 years placing the fill layerShow sample (hand) calculation at a depth of 41 ft and the timing of 10 years after placingthe fill layer. can you show your work on…
(e) A soil profile consists of a clay layer between layers of sand, the water table being in theupper sand layer. Before the construction of a raft foundation for a large reservoir, piezometers were placed in the saturated clay layer. The whole process of filling the reservoir may be approximated to applying rapidly a single pressure increment of 200 kPa uniformly throughout the clay layer. One year after filling the reservoir, the piezometers indicated a distribution of excess porewater pressure as indicated in Figure Q-e. Estimate the average degree of consolidation at this time.
Q₂/ From the result which obtained from consolidation test on a sample of clay soil at depth (3.5 m). Show if the soil is (N.C.C) or (O.C.C), if you know: (y sat = 18.82 kN/m³). Pressure Void ratio 0 0.903 25 0.865 50 0.843 100 0.795 200 0.730 400 0.651 800 0.555 1600 0.468 400 0.501 100 0.547 25 0.583 0 0.612
Please show me steps I am studying for exam
A clay layer 5 m thick has double drainage. It was consolidated under a load of 127.5 kN/m2. The load is increased to 197.5 kN/m2. The coefficient of volume compressibility is 5.79 x 10^-4 m2/Kn and value of k = 1.6 x 10^-8 m/min. If the test sample is 2 cm thick and attains 100% consolidation in 24 hours, what is the time in days taken for 100% consolidation in the actual layer? a. 62,500 b. 60,000 c. 65,000 d.67,500
Consider point P. If the groundwater drops 1m to the top of the clay layer, what would the change in Total Stress and Pore Water Pressure change? 1 m 1m 2m 2m P Sand Clay Sand Pd = 1.35 Mg/m³ Psat 1.85 Mg/m³ H Psat = 2.0 Mg/m³ Psat = 1.9 Mg/m³
It is known that a particular deposit of clay has the following shear strength parameters: c' = 15 kPa, o' = 23°; Cu = 10 kPa, cu = 13° A sample of this clay is consolidated in a triaxial cell to an all-round pressure (03) of 250 kPa. The sample is then sheared by increasing 0₁, keeping 3 constant and the drainage valve closed. What is: i) ₁ at failure? ii) Pore water pressure inside the sample at failure? iii) Final values of 0₁' and 03'? iv) Value at failure of Skempton's pore pressure coefficient A?
A stratum of a clay 5 m thick is sandwiched between highly permeable sand strata. A sample of this clay, 25 mm thick, experienced 50% of ultimate settlement in 12 minutes after the application of a certain pressure. How many days will it take for a building proposed to be constructed at this site, and which is expected to increase the pressure to a value comparable to that applied in the laboratory test, to settle 50% of the ultimate value? a. 356 b. 346 c. 333 d. 521
Question 9 Three samples of loose sand were tested under consolidated undrained (CU) conditions. The failure stresses and excess pore water pressure for the soil sample is given below: Cell Pressure = 201 kPa Deviator Stress = 127 kPa Pore Water Pressure = 95 kPa Determine the drained angle of inclination of failure plane in degrees. Round off to two decimal places.
Please check and provide answers
A specimen of normally consolidated clay was consolidated under a chamber confining pressure of 280kpa for a drained test by how much does the axial stress have to be reduced to cause failure by axial extension?