Print and solve this problem, OB1- 16.2 lb OB1-7.2 lb OB1-5.5 lb OB1-36.5 lb OB1- 12.1 lb O None of these. OB1-19.3 lb The 75th uniform cellar door is held in place by the hinges at A and B and the tension in rope CD. Hinge B does not support any axial thrust. Find the reaction B₁. Point D is in the xy plane. Given: 32in 78 16in 48 T=(8.997 +32.47-22.6K)b 30° T D(48, 32, 0) 16 B 36 Answer(s): +B₁ Reactions at hinge

Print and solve this problem, OB1- 16.2 lb OB1-7.2 lb OB1-5.5 lb OB1-36.5 lb OB1- 12.1 lb O None of these. OB1-19.3 lb The 75th uniform cellar door is held in place by the hinges at A and B and the tension in rope CD. Hinge B does not support any axial thrust. Find the reaction B₁. Point D is in the xy plane. Given: 32in 78 16in 48 T=(8.997 +32.47-22.6K)b 30° T D(48, 32, 0) 16 B 36 Answer(s): +B₁ Reactions at hinge

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The homogeneous bar AB weighing 1800 lb is supported at either end by a steel cable. Calculate the smallest safe area of each cable if the working stress is 18 000 psi for steel. 2ft 1.5 ft a. 0.075 in? c. 0.100 in? d. 0.050 in? 5ft b. 0.128 in? Ans:
Why clamp handles are used?
The compound beam is pin supported at C and supported by a roller at A and B. Note that there is a hinge at D. Find the reactions at the supports. Neglecting the thickness of the beam. (Provide the whole solution along with its FBD)
please answer question below step by step fill in all blanks v and m diagram fbd and final fbd
Determine end reactions for Beam B-1 and Girder G-1. B-1 1 F1 • L1= 24 ft L2= 6 ft Live load 30 psf 4" Thick concrete slab (density = 150 pcf) . 5/8" Thick terrazzo (12 lb/ft2/in) • Beam weight = 35 lb/ft . Girder weight = 26 lb/ft Please round to the nearest one. One end reaction for B-1 = lbs One end reaction for G-1 = lbs Please answer all parts of the question. 20 DOO 000 F2 @ 2 JAL #3 G-1 F3 54 $ F4 % 5 F5 L2 L2 L2 L2 MacBook Air F6 A 6 & 7 F7 11 ► 11 * 8 F8 F9
Please answer completely will give rating surely
question 13 two decimal places
The steel pipe is filled with brass and subjected to a torsion T=34kNm. Determine each torsion value T, and T, taken by steel and brass. S Take the shear modulus for steel G,=80GPA and for brass G,=40GPA. T=34kNm cross-sect lon of A-B 2- steel 1- brass d,=12cm 100cm d;=4cm
"D.35. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 25.8 MPa, fy= 506.8 MPa, bf= 710 mm, t= 90 mm, hw= 470 mm, bw = 440 mm ds= 10 mm, ct- 30 mm, cb = 35 mm. Steel bar details: compression side at top (single layer): 4- 16 mm dia. , tension side (double- layered): upper layer is 4 - 28 mm dia. and lower layer is 5 - 28 mm dia." Use the editor to format your answer br ... Ct Bar diameters and positioning in the figure given are just representations. Refer to the problem statement for the ds hw number of bars and bar diameters to use in your computation. 25 mm Cb bw
Determine the vertical external reaction at the pin support.
The floor system shown below supports a uniform dead load of 100 lb/ft² and a uniform live load of 40 lb/ft?. Draw the loads with magnitudes on the following structural members: а) BI b) В2 с) ВЗ d) B4 e) Gl f) G2 g) G4 6 @ 7' = 42' C4 G1 B3 B2 2 @ 15' = 30' G4 G3 G2 BT 5 @ 6' = 30' 42' 36' For the same floor plan shown above and assuming the same floor loads and that the building consists of four floors, determine the following: a) The dead load on column Cl in the first floor. b) The live load on column C2 in the second floor. Consider live load reduction. c) The sum of the dead plus live loads on column C3 in the third floor. Consider live load reduction. OT
Question 4) Check the maximum permissible A, to ensure ductile behavior. Compute the design moment strength øMn. Use fy = 60000 psi and f = 4000 psi. %3D -6 in.- 3 in. 2 #9 6 in. 12 in, 30 in. 6 in. 5 #11 3 in. 3 in. +4 @ 3 in. = 12 in. +3 in. 18 in.-