PRESTUDY 3. Using the physical properties you entered in the table and the outlined experimental procedure, complete the flow chart. In the oval spaces, name the reagents and/or conditions necessary to affect each indicated separation step. In the rectangular boxes, write the names of the separated components. Mixture of NaCl, SiO₂, Fe co SiO₂ and NaCl magnet EME08 PPPS Tako Laturitas o Fe 28

PRESTUDY 3. Using the physical properties you entered in the table and the outlined experimental procedure, complete the flow chart. In the oval spaces, name the reagents and/or conditions necessary to affect each indicated separation step. In the rectangular boxes, write the names of the separated components. Mixture of NaCl, SiO₂, Fe co SiO₂ and NaCl magnet EME08 PPPS Tako Laturitas o Fe 28

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

You were tasked to separate the components of a mixture containing silica, sodium chloride and charcoal. TNāCI dissolves in water while silica and charcoal are not water-soluble. Only charcoal dissolves in carbon disulfide. a. Write a short experimental procedure to carry out the separation of the mixture. b. Given the following data, determine the percentage of charcoal, sodium chloride and silica. Mass (g) Mass of beaker 100.000 Mass of beaker + mixture 110.000 mass of evaporating dish 62.000 mass of evaporating dish + solid after evaporation of water 65.000 Mass of beaker + charcoal + silica after evaporation of excess water 117.000 mass of beaker + silica after decanting dissolved charcoal and drying 113.545
A 1.250 g sample of bauxite (the primary ore of aluminum) was analyzed for aluminum. The sample was powderized and treated in concentrated nitric acid. The nitric acid was removed and solids were treated in hot water with added nitric acid. Insoluble solids were removed by gravity filtration. The solution was made basic by the slow addition of dilute ammonia forming the gelatinous precipitate (Al(OH), and Al,O,.x H2O). The precipitate was heated to coagulate it then filtered over filter paper. The paper and solids were placed in a porcelain crucible and the paper was ashed while the precipitate was ignited at 600°C to convert the precipitate to pure Al,O,. The mass of Al,O, recovered was 0.2890 g. The average mass of ash after charring 10 sheets of the identical filter paper was 0.0007 g. Calculate the percent aluminum in the bauxite ore sample.
A 0.879 g sample of a CaCl2·2H2O/K2C2O4·H2O solid salt mixture is dissolved in ~100mL of deionized water. The precipitate, after having been filtered and air-dried, has a mass of 0.284 g. The limiting reactant in the salt mixture was later determined to beCaCl2 ·2H2O. a.Write the ionic equation for the reaction. b.Write the net ionic equation for the reaction. c.How many moles and grams of CaCl2 ·2H2O reacted in the reaction mixture? d.How many moles and grams of the excess reactant, K 2C2O 4H2O, reacted in the mixture? e.How many grams of the K2C2O4·H2O in the salt mixture remain unreacted (inexcess)? f.What is the percent by mass of each salt in the mixture
A piece of Gold weighing 12,359 Kg is suspected of being contaminated with Iron. To perform an instrumental analysis and To confirm whether or not it contains Fe, a portion of the sample (0.954 g) is taken from the piece and dissolved with 25 mL of aqua regia. Heats up For its complete dissolution, it is cooled and made up to 100 mL. A 10 mL aliquot is taken from this solution and made up to 50 mL. From This last solution is given the appropriate treatment to visualize Fe+2, for which the 1,10-phenanthroline reagent is added. (it forms a complex that is red in color) and is taken to a visible spectrophotometer and with a 12 mm cell a absorbance of 0.45. Previously, a calibration curve of Fe+2 was obtained under the same instrumental conditions obtaining the following data: (view table) Calculate the purity of the gold piece, assuming impurities only due to Fe.
List and define the indicators that are used to assess the performance of a specific analytical method under specified conditions.
Using the data and formula shown, Determine the concentration of iron in the sample and its standard deviation from the least-squares equation of the line. Compare the unknown concentration to that obtained manually from a calibration curve.
You were assigned to assay a product sample of milk of magnesia. A 0.600-g sample was reacted with 25.00 mL 0.10590 N H2SO4 . The excess unreacted acid in the solution required 13.00 mL of 0.09500 N NaOH when titrated to reach the methyl red end point. Determine the dosage strength of the product in terms of % Mg(OH)2 content. Type your answer in 2 decimal places, numbers only.
4 What will be the ideal precipitating agent in gravimetric analysis? Select one: O React to all elements in Alkaline metals, Alkaline earth metals, and Halogens. O Produce a precipitate that is sparingly soluble. React only to the constituents of the atmosphere. O Produce a precipitate of unknown chemical composition after it is ignited.
The Kjeldahl method was used to determine the nitrogen content of a protein. A 275 µL aliquot of a 47.0 mg/mL protein solution was digested in boiling sulfuric acid. The solution was made basic and the liberated NH, was collected in 5.00 mL of 0.0512 M HCl. A volume of 7.00 mL of 0.0174 M NaOH was required to react with the excess HCl. Calculate the weight percent of nitrogen in the protein. weight percent: wt% N
How many moles of H2 are produced from 0.1000g of zinc? Please show how you got your answer. Zn+2HCI-->ZnCl2+H2
Dilute the stock solution: Using the solutions in the burets, carefully measure the following quantities of Co(NO3)2 solution and water into 5 large test tubes, to a total of 5.00 mL in each test tube. Yes, the optional video says to make 10.00 mL total, but 5.00 mL is sufficient at this time and generates less waste. Use the buret to measure the cobalt solution and the water. Test tube No. 1 2 3 4 5 mL Co2+ Soln 1.00 2.00 3.00 4.00 5.00 mL H2O 4.00 3.00 2.00 1.00 0.00 Total mL 5.00 5.00 5.00 5.00 5.00 Mix each test tube thoroughly: hold the top of the tube and mix the bottom well. Transfer a portion of each diluted sample into a clean, dry sample cuvette. fill the concentration table and do calculations please
If the mass of the original sample of alloy was 0.7459 + 0.0005 g and the mass of precipitated CuSCN was 0.2275 ± 0.0005 g and the volumetric flasks used had a 0.05% error, what is the error in the calculated percentage mass of Cu in the alloy? Assume no error in the molecular masses. Provide your answer as an absolute error.