pressure of 10 kPa gage is applied to the surface of water in an enclosed tank. The distance from the water surface to the outlet is 0.5 m. The outlet pipe is exposed to the at

Q: An air compressor takes in 12m3 /min of air (measured at atmospheric conditions of 101.3 kPa, 15o c)…

A: Given data An air compressor takes in 12m3 /min of air (measured at atmospheric conditions of 101.3…

Q: A 3.5-hp pump delivers 1140 lbf of ethylene glycol at 20°C in 12 seconds, against a head of 17 ft.…

A: Calculate the efficiency of the pump in %.

Q: Water is flowing in a pipe with a velocity of 2 m/s and a pressure of 2.5 bar. The nozzle which is…

A: Given data P1=2.5 barV1=2 m/secV2=20 m/sec

Q: 3. Water flows at a average velocity of 3m/s into a nozzle that reduces the diameter from 10cm to…

A:

Q: A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A:

Q: Q2) A vertical wall is of 8 m in height as shown below. If a jet of water is coming out from a…

A:

Q: A pump draws benzene at 25°C from a tank whose level is 2.6 m above the pump inlet. The suction line…

A: Atmospheric pressure=98.5kPa Vapour pressure = 13.3kPa Head loss= 0.8m To find net positive suction…

Q: Water with a specific heat of 1 BTU/lbm F is pumped using a 1-hp jet pump from a well that is 20 ft…

A: Given       Specific heat, C = 1 BTU / lbm           Flow rate, m = 5 gal/min…

Q: Water with a density of 1.94 slug/ft³ is in a cart. Water is ejected from the cart with a velocity…

A:

Q: Include a free body diagram. A 100-mm-diameter jet of water is discharged (horizontally) from a…

A:

Q: Air moves through a tube that has a radius of 0.6 cm. If conditions are at STP, find the critical…

A:

Q: find the speed up with which it flows inside the hose.

A:

Q: Water enters a turbine through a 320mm diameter pipe at the rate of 215 lit/s at a pressure at A of…

A: given data  diameter at A = 320mm flow rate = 215 lit/s pressure at A = 150kpa pressure at B = -35…

Q: Water is flowing in a pipeline at 64 li/sec. If the diameter of the pipeline is 120 mm, calculate…

A:

Q: The pump is used to increase the pressure of water from 100 kPa to 900 kPa at arate of 160 L/min. If…

A:

Q: An irrigation pump delivers water through a 6 - inches horizontal pipe flowing full at the outlet,…

A: If an object travels with constant velocity, then the motion of the object is said to be uniform…

Q: ind the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect…

A: Write the Bernoulli expression as follows.

Q: A water truck drives slowly around a construction site, spraying water to keep dust down. A pump…

A:

Q: If the wind velocity is: 1 m/s, 2m/s, 3m/s, 5m/s 7m/s turbine will be:

A:

Q: 3-56. A 2-in. Younded orifice exists in the horizontal bottom of a large tank. The water in the tank…

A: According to the given data H=12ft h=6ft Cc=1 d=2in=0.16667 ft we need to find  Discharge of the…

Q: At atmospheric pressure of 100 kpa exists inside a room. Air is exhausted through a 0.5m diameter…

A: The fan capacity if the operating speed is changed to 1200rpm is 0.667 m3/s.

Q: Q.2: This system of blades develops 149kW under the influence of the jet shown. Calculate the blade…

A: Given   Jet velocity, V1 = 90 m/s   Jet diameter, d = 25 mm                 Angle = 30o Find   Blade…

Q: Air enters the room through a 200 mm diameter pipe and exits the fan into the ambient air through…

A:

Q: A  25Hp  suction pump operating at   56.30%  efficiency draws water from a suction line whose…

A: The power of the pump is P=25 Hp The efficiency of the pump is η=56.3%. The diameter of the suction…

Q: Q5. Two tanks A and B of surface areas 600 m2 and 300 m2 are connected by an orifice of 0.18 m2 in…

A:

Q: Patm A water Tank C hi h2 As shown in the figure, at hi= 1.8 m, h2= 3.6 m positions, the water in…

A:

Q: Water flows through the reducer, the inlet diameter is 20 cm and the outlet diameter is 10 cm. If…

A: Given:-  Inlet Conditions : Diameter (D1) = 20 CM = 0.20 m Velocity (C1) = 0.4 m/s Pressure (P1) =…

Q: ine a fluid packet moving through the Orifice plate. What happens when it’s Kinetic Energy as it…

A:

Q: Water is passing from the nozzle having an inlet area is 0.08 m2 and velocity is 5 m/s, the outlet…

A: Given: Inlet area, A1=0.08 m2 Outlet area, A2 =0.05 m2 Velocity in the inlet of nozzle, V1= 5 m/s

Q: Water enters a turbine through a 320mm diameter pipe at the rate of 215 lit/s at a pressure at A of…

A:

Q: 1.000 kg of saturated liquid water at 150°C is heated at constant pressure in a piston-cylinder…

A: Approach to solving the question:Please see attached photos for detailed solutions. Thank you.…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.