Pressure gage B (s. Figure G) is to measure the pressure at point A in a water flow. If the pressure at B is 87 kPa, estimate the pressure at A in kPa.

Q: A two-pond system is fed by a stream with flow rate 4 m^3/d and BOD concentration 50.0 mg/L, as…

A: The schematic labelled diagram for the given process is shown below. Here,Q = flow rate = 4…

Q: 4. Rework inviscid flow past a cylinder in terms of the stream function y.

A: The inviscid flow past a cylinder in terms of stream function is to be mentioned.

Q: A 4 inch Sched 40 steel pipe carries crude oil at 80°C. The crude oil has a dynamic viscosity of 1.2…

A: Given: 4 inch Schedule 40 steel pipe dynamic viscosity μ =1.2 x 10-2 Pa·s density ρ= 680 kg/m3

Q: Estimate the mass, kg, and weight, N, of the air contained in a classroom with STP conditions.…

A: The dimension of the classroom: 3.2m x 8m x 20m Air is at STP i.e. Standard temperature and pressure…

Q: Determine the magnitude and direction of the anchoring force needed to hold orizontal elbow and…

A: Given that  At section 1 Pressure,P1 = 100 kpa ( gauge pressure ) Velocity,V1 = 2m/s  Diameter ,d2…

Q: In a homogeneous isothermal liquid polymerization, 20% of the monomer disappears in 34 minutes for…

A: 20 % disappearance of monomer in 34 minutes, so   t = 34 minutes CA = 0.8 CA° Where CA° is initial…

Q: 8. Oil flows in the pipe shown in figure. The orifice in the pipe has a coefficient of discharge of…

A: The orifice meter is a flow measuring device. The difference in pressure gives the flow rate of the…

Q: -1. An incompressible fluid is flowing at steady state in the annular region (i.e., torus or ring…

A: Given Incompressible fluid Take inner radius = r2 Outer radius = r1

Q: In order to understand all issues regarding the analysis of flow around a sphere, first (a) Argue…

A: Hello!  Since you have posted a question with multiple sub-parts, we will solve first three subparts…

Q: The following reaction is carried out at a certain temperature, which yields the data below.…

A: In chemical reaction engineering, the rate law is described as an expression that provides a…

Q: A liquid flows under steady state conditions along an open channel of a fixed inclined planeto the…

A: Given Question is explained in detail.Explanation:Step 1: a) Factors affecting the depth of the…

Q: Water is in steady fully developed laminar flow between two horizontal, very wide (W) and long (L)…

A:

Q: Which of the following statement is TRUE? (A) Friction factor f in laminar flow depends on the…

A: WE KNOW THAT,  Pressure drop = △P = 32 μVLD2  WHERE, V = velocity  if we doubled the velociy V2 =  2…

Q: A water pipe is connected to a double-U manometer as shown in Figure below at a location where the…

A:

Q: 1. An incompressible fluid of kinematic viscosity v= p/p = 10-4 m²/s flows steadily through a…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: For the configuration shown in Figure 1, calculate the weight of the piston if the gage pressure…

A:

Q: Parallel laminar Flow Between Infinite Planes with a Manometer A Newtonian fluid with viscosity μf…

A:

Q: True or false: Osmotic pressure can be explained by the difference in fugacities

A: It is to be mentioned whether fugacity difference explains the osmotic pressure or not.

Q: Kerozene Air Z10 cm 9 cm 20 cm 14 cm 8cm Benzeue Water Mercury 1,2 kg/m3 : 13550 bg/m3 mercury Air…

A:

Q: express in 4 decimal places    ans asap

A:

Units and Dimensions

Dimensions are the basic concepts of the measurement of quantities. Units are the means of expressing the dimensions. For instance, an area has a dimension of L2 and a unit of m2.