A pressure drop of 500 kPa is measured over 200 m of a horizontal length of 8-cm-diameter cast iron pipe transporting water at 20–C, friction factor is 0.026 andkinematic viscosity of the water is 1.004*10-6 Fined:1. The relative roughness.2. The head loss.3. The average velocity.4. Reynolds number.5. Volume flow rate.

pressure drop of 500 kPa is measured over 200 m of a horizontal length of 8-cm- iameter cast iron pipe transporting water at 20–C, friction factor is 0.026 and inematic viscosity of the water is 1.004*106 Fined: 1. The relative roughness. 2. The head loss. 3. The average velocity. 4. Reynolds number. 5. Volume flow rate.

pressure drop of 500 kPa is measured over 200 m of a horizontal length of 8-cm- iameter cast iron pipe transporting water at 20–C, friction factor is 0.026 and inematic viscosity of the water is 1.004*106 Fined: 1. The relative roughness. 2. The head loss. 3. The average velocity. 4. Reynolds number. 5. Volume flow rate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

for line Pife i Daen Daimetel omm Q = 1. 6 LI m.n Dhact = 26 Cm Determing %3D BQ m/s m/s (3) oh theo Re at tube length To cm
In the design of a 500m long water pipeline it is proposed to keep head loss, hf, less than 6m for a flow of 0.50 m's1. The pipeline must also be able to withstand water hammer pressures under rapid valve closure condition at the discharge end. Two types of pipes- PVC and steel - each 50 cm in diameter are available. Which pipe will you recommend? 1. The Darcy friction coefficient, 2, can be estimated from Figure 1. The value of the roughness height for steel pipe is 0.00015m, while the PVC pipe can be considered hydraulically smooth. The thickness of each pipe is 1 cm and the Modulus of Elasticity, E, for steel is 200x10° Nm2 and for PVC is 1.7×10®N%?. The Bulk Modulus of Elasticity, K, for water is 2x10°Nm2. The working pressures for the steel and PVC pipes are 2 MPa and 1 MPa respectively. 0,1 0,09|Laminar flow f IN aica Transition 0,08 Laminar Critica! flow Complete turbulence, rough pipes Zone 20ne 0,05 0.07 0,04 0,06 0,03 0,05 0,02 0,015 Lio 0,04 0,01 0.008 Re, 0,006 0,03 0,004…
Complete soln pls. Use the moody chart when the factor "f" is to be determined
For fl ow of water at a Reynolds number of 1.03 E6 througha 5-cm-diameter pipe of roughness height 0.5 mm, theapproximate Moody friction factor is(a) 0.012, (b) 0.018, (c) 0.038, (d) 0.049, (e) 0.102
Gasoline at 20°C fl ows at 3 m3/h in a 6-cm-diameter pipe.A 4-cm-diameter thin-plate orifi ce with corner taps isinstalled. Estimate the measured pressure drop, in Pa.
I need the answer quickly
How to calculate permeability according to silica bead characxteristics without knowing pressure drop? silica diameter: 2.5mm Inlet mass flow rate: 0.3m^2/min Inlet Temperature: -10 degree C
with a head loss of 7.5-m. Use iterative method to find the pipe diameter requires to keep a flow Q3: Oil, with (p- S950 kg/m'; v 2x10s m2/s), flows through horizontal smooth pipe of 80-m long rate of 0.332 m/s steadily flowing, (Start with initial guess of friction factor f-0.01)
Two-phase pipeline with 0.2 m diameter and 3000 m length. The inlet pressure = 2300 kPa, liquid flow rate = 0.01 m³/s, volumetric Gas Oil Ratio = 44, pr-680 kg/m³, pg-0.93 kg/m³, gas viscosity-0.015x10-³ Pa.s, and liquid viscosity = 9.4x103 Pa.s. If new gas pipeline with flow rate (0.09 m³/s) connects to the middle of the existing pipeline, calculate the pressure at the outlet of existing pipeline?
watu enters a tube (d=6omm) ta rate of o.ol Kals with temp. of 2öc . A constant het flux of 2000 winh was applied. What rs the tube length requined to obtain an exit temp. of såc. what is the surface temp.t the outlet of the tube, where fully developed conditions maybe assumed to exist. -