SAE 10 oil at 20°C (y = 8.52 kN/m³, p = 860 kg/m³, u = 8.14 x 10-2 N-s/m2) is to flow through a 300-m level concrete pipe. What size pipe will carry 0.0142 m2/s with a pressure drop due to friction of 23.94 kPa? Ans. 156 mm

SAE 10 oil at 20°C (y = 8.52 kN/m³, p = 860 kg/m³, u = 8.14 x 10-2 N-s/m2) is to flow through a 300-m level concrete pipe. What size pipe will carry 0.0142 m2/s with a pressure drop due to friction of 23.94 kPa? Ans. 156 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8. A horizontal pipe has a non-negligible expansion (K, =(1 Asmall Atarge/ ) as shown in the figure. The water flows through the pipe and the velocity (V1) and the pressure (P:) in the smaller-diameter pipe are 10 m/s and 300 kPa, respectively, and the flow is turbulent. Assume that the major loses are negligible, kinetic energy correction factor is 1.06 at both the inlet (a1) and the outlet (a2), and the density of water is 1000 kg/m?. a) Determine the outlet pressure P2 considering the losses and kinetic correction factor b) find the error that would have occurred if Bernoulli's equation had been used ignoring all the losses and the kinetic energy correction factor. 8 cm 16 cm Water
In the design of a 500m long water pipeline it is proposed to keep head loss, hf, less than 6m for a flow of 0.50 m's1. The pipeline must also be able to withstand water hammer pressures under rapid valve closure condition at the discharge end. Two types of pipes- PVC and steel - each 50 cm in diameter are available. Which pipe will you recommend? 1. The Darcy friction coefficient, 2, can be estimated from Figure 1. The value of the roughness height for steel pipe is 0.00015m, while the PVC pipe can be considered hydraulically smooth. The thickness of each pipe is 1 cm and the Modulus of Elasticity, E, for steel is 200x10° Nm2 and for PVC is 1.7×10®N%?. The Bulk Modulus of Elasticity, K, for water is 2x10°Nm2. The working pressures for the steel and PVC pipes are 2 MPa and 1 MPa respectively. 0,1 0,09|Laminar flow f IN aica Transition 0,08 Laminar Critica! flow Complete turbulence, rough pipes Zone 20ne 0,05 0.07 0,04 0,06 0,03 0,05 0,02 0,015 Lio 0,04 0,01 0.008 Re, 0,006 0,03 0,004…
What’s the answer for this please ?
Ex ....... HYDRAUE • The pump is to be connected to a rising main which has a diameter (D) of 400 mm and a length of 137 m.The entry exit and minor head losses in the pipeline can be taken as 80D in this particular situation. The friction loss can be approximated by h; = ALQ² / 1 2D5 with A=0.04. The static lift is 10 m. By considering a single pump (P). And two of the pumps in series (P+P) and parallel (P//P) determine: > the H-Q curve of the two pump combinations » Which combination will be capable of discharging at least 0.3 m³/s, with the ability to pump up to 0.35 m³/s if the need arises. %3D
plzzzzzzz help me its urgent
The water is delivered with piping system given in the figure below. The levation difference between entering section and tank is 143,55 m. Estimate the gage pressure [MPa] at point 1. (Note: For water at 20°C, take p=998 kg/m and u=0.001 kg/ms. ) 5 cm diameter cast-iron pipe Length of the system is 1.2 km All fittings are flanged. The vohume flow rate is 300 L min 45 treaded elbow Yanit
the fluid in a pitot tube is mercury (sg = 13.6) having deflection of 30 cm. calculate the rate of flow in L/s in the 100mm tube if the flowing fluid is oil (sg=0.82). neglect the headloss in the pipe. Answer: 75.2
Question 3 Water flows through a 2-in.-diameter (5.08 cm) tube that suddenly contracts to 1 in. diameter (2.54 cm). The pressure drop across the contraction is 3.45 kPa. Determine the volume flow rate. Minor Loss Coefficients for Pipe Entrances Entrance Type Reentrant Minor Loss Coefficient, Ka 0.78 Square-edged Rounded "Based on h-K(V2/2), where V is the mean velocity in the pipe. Contraction loss coefficient, K [ h = Kc \ /² ] 0.5 r/D K 0.02 0.06 ≥ 0.15 0.28 0.15 0.04 Contraction Expansion A1 A2 A₂ AR Ag/A = AR = A₁/A2 1.0 0.8 0.6 0.4 0.2 0.2 о T ° 0 0.2 0.4 0.6 0.8 1.0 Area ratio, AR 1.0 OOOO 0.8 0.6 Expansion loss coefficient, K Loss coefficients for flow through sudden area changes.
Compute the head loss (in meters) in 3000 m of horizontal, cast iron pipe with nominal pipe size of 350 mm and SCH 60. The pipe carries water with an average velocity of 2.1 m/s. Take water at 20°C to have a viscosity of 1.00E-3 Pa-s and density of 1000 kg/(m^3). Take the roughness of steel pipe to be 0.26 mm. Note: Use the Tioga table of pipe dimensions and weights as reference. Round your answer to 2 decimal places.
PROBLEM 3 Water, p = 1000 kg/m³ and μ = 0.001 kg/m.s, is pumped between two reservoirs at 5 liter/s through 125 m of 5 cm-diameter pipe and several minor losses, as shown in Fig. The roughness ratio is e/d= 0.001. Compute the pump horsepower required. 2₂= 40m Screwed regular 90° elbow Sharp exit Ģ2 1 2₁ = 7m GI Sharp entrance Half-open gate valve Open globe valve 30 cm bend radius 125m of pipe, d= 5 cm Pump
Dev