Practice Problem 4.5 A rectangular beam has a width of 320 mm and an effective depth of 570 mm. Concrete cover is 60 mm from the centroid of bars. Concrete compressive strength, f'c= 24 MPa. Steel yield strengths are 415 MPa for longitudinal bars and 275 MPa for hoops. Stimups are placed in 2 layers with a diameter of 10 mm. Detemine the required spacing of the stimups when a) The required strength Vu is 50 kN b) The required strength Vu is 90 kN c) The required strength Vu is 130 kN d) The required strength Vu is 290 kN e) The required strength Vu is 360 kN f) The required strength Vu is 570 kN

Practice Problem 4.5 A rectangular beam has a width of 320 mm and an effective depth of 570 mm. Concrete cover is 60 mm from the centroid of bars. Concrete compressive strength, f'c= 24 MPa. Steel yield strengths are 415 MPa for longitudinal bars and 275 MPa for hoops. Stimups are placed in 2 layers with a diameter of 10 mm. Detemine the required spacing of the stimups when a) The required strength Vu is 50 kN b) The required strength Vu is 90 kN c) The required strength Vu is 130 kN d) The required strength Vu is 290 kN e) The required strength Vu is 360 kN f) The required strength Vu is 570 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The design engineer specifies a concrete strength of 37.92 MPa. Determine the required average compressive strength for: a. a new plant where s is unknown b. a plant where s = 3.45 MPa for 22 test results c. a plant with extensive history of producing concrete with s = 2.76 MPa d. a plant with extensive history of producing concrete with s = 4.14 Mpa
The T-section shown is subjected to a design ultimate moment of M = 180kN.m. Find the required area of reinforcement given a 10% redistribution of moments was applied in determining The Moment. please give explanations with the steps and diagrams
A simply supported beam shown in figure 1, carries an uniform service (unfactored) superimposed deadload of 1.4 kips/ft. plus its own weight and a liveload of 1.5 kips/ft. The concrete strength is 3,500 psi, and the yield strength of the reinforcement is 60,000psi. The concrete is normal- weight concrete. Use the load and strength reduction factors from ACI Code. Compute the design strength or capacity at the midspan of the beam and check if it is safe or adequate to resist the factored service moment. a). 220 kips-ft., safe Figare li wds 14 kipplr.; We= 1,5 kips /. し,vbv b). 336 kips-ft., safe 215" c). 128 kips-ft., inadequate 3 ho. 9 ars d). 255 kips.ft., adequate Solution:
The design engineer specifies a concrete strength of 31.0 MPa (4500 psi). Determine the required average compressive strength for:a. a new plant for which s is unknownb. a plant for which s = 3.6 MPa (520 psi) for 17 test resultsc. a plant with extensive history of producing concrete with s = 2.4 MPa (350 psi)d. a plant with extensive history of producing concrete with s = 3.8 MPa (550 psi)
Please answer letter g.
A doubly reinforced concrete beam of size 250 mm x 500 mm overall depth is reinforced with 2-12 mm dia. bars in compression zone and 3-20 mm dia. bars in tension zone, each at an effective cover of 40 mm. The grade of concrete and steel are M20 and Fe415 respectively. The strain in compression steel will be [Take stress in compression steel as 345 MPa]
I need the answer as soon as possible
I need solve this question in concrete by ACI CODE
The loadsshown on the beam with a cross section at midspan as shown, are service (unfactored)loads. The concrete used is a normal weight concrete with compressive strength of 4000 psi.The yield strength of the reinforcement is 60,000psi. For the midspan section shown, computeφMn and show that it exceeds Mu
A rectangular beam has the dimensions b=12in., h=26in., and d=24 in. and is reinforced with three No. 11 bars so that As-4.68 in.². The normal-weight concrete compressive strength is 5000 psi. and the tensile strength (modulus of rupture) can be calculated as per ACI318-14. The Grade of the steel is 60. Determine the nominal moment strength M, and the moment capacity Mn. b=12 in. Figure 1. d=24 in. h=26 in.-
A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced with a single high strength steel bar that has a cross- sectional area of 0.42 in2.The bar has a normal tensile strength of 145 ksi, linear stress-strain curve to failure, and a strain at failure of 1.8 percent. The concrete strength fc= 6000 psi. Calculate the nominal flexural strength of the section.
A continuous beam 250 mm x 450 mm carries 6 numbers of 12 mm diameter longitudinal bars as shown. The factored shear force at the point of inflection is 200 kN. Check if the beam is safe in bond. Assume M15 mix with ok = 15 N/mm2 and mild steel with o, = 250 N/mm2. A clear %3D cover of 25 mm canbe assumed. The design bond stress for mild steel bars in M15 concrete is specified to be 1.0 N/mm2. Section of point of inflection 6 no's of 12 mm dia