Practice Problem 1,2 A 60 - cycle, 150 kVA, three winding transformer is rated at 4,800 volts primary voltage, and there are two secondary windings, one rated at 720 Volts and the other at 240 Volts. There are 360 primary turns. The rating of each secondary winding is 75 kVA. Determine (a) turns in each secondary winding: (b) rated primary current at unity power factor; (c) rated primary current at 0.707 power factor lagging current; (d) rated current of the 600-Volt and 240-Volt secondaries at unity power factor. Answers: (c) I, = 31.25/-45" Amp. 104.167 /Q" Amp.; (a) NSI = 54 turnsi N = 18 turns (b) I, 31.25/0" Amp. (d) 312.5/0" Amp. %3!

Practice Problem 1,2 A 60 - cycle, 150 kVA, three winding transformer is rated at 4,800 volts primary voltage, and there are two secondary windings, one rated at 720 Volts and the other at 240 Volts. There are 360 primary turns. The rating of each secondary winding is 75 kVA. Determine (a) turns in each secondary winding: (b) rated primary current at unity power factor; (c) rated primary current at 0.707 power factor lagging current; (d) rated current of the 600-Volt and 240-Volt secondaries at unity power factor. Answers: (c) I, = 31.25/-45" Amp. 104.167 /Q" Amp.; (a) NSI = 54 turnsi N = 18 turns (b) I, 31.25/0" Amp. (d) 312.5/0" Amp. %3!

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuits are 200,400 volts, respectively, at a frequency of 50 Hz The primary no-load current at voltage 200 equals 0.7 amps and pulp losses equal to 70 watts Primary resistance and reactance 3.2 , 1.25 In order, the reactance of the resistance and the coil 0.6 , 0.7 Then draw the equivalent circle, explaining the values
Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no-load voltages in the primary and secondarypement are 200 and 400 volts, respectively, with a trend of 50 Hz. The no-load current at 2, 50. Voltage 200 volts is equal to 0.7 amperes, and the cores are equal to 70 watts, 1.25 ohms, respectively, the resistance and reactance of the secondary 0.6, 7... Ohms, respectively. Draw the assigned circle Explaining the values of its elements.
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux C) Total flux B) Mutual flux D) Leakage flux 5. The ------- are represented in the induction motor equivalent circuit by the resistor Rc (or the conductance Gc). A) Stray losses. C) Air-gap losses B) Friction and windage losses D) Core losses 6. The per-phase voltage Vo can be calculated by dividing the total voltage on. A) √3 B) √1.404. C) √0.707. D) √2.
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux B) Mutual flux D) Leakage flux C) Total flux 5. The fundamental component of the magnetization current ------- the voltage applied to the core by ------ 90°: A) Lags, 45° B) Leads, 45°. D). Leads, 90°. C) Lags, 90°. 6. The ----- are resistive heating losses in the core of the transformer. A) Hysteresis losses. B) Copper losses. C) Leakage flux losses. D) Eddy current losses. 7. The total rotational losses of an induction motor are a combination of: A) Friction losses B) Windage losses. C) Core losses. D) Stray losses. 8. Induction motors are now the preferred A) absence of brushes. choice for industrial motors due to B) Small size. C) Less control requirements. D) rugged construction. 9. For an induction motor, if the synchronous speed is 1800 r/m, and the rotor speed 180rad/sec, then the slip will be: A) 5.5 % C) 6% B) 4.5% D) 4% 10. The lower the speed of an…
UDng a ITIe Core in high frequency transformers. c- Discuss, different applications of iron cores of different hysteresis loops. d- Explain the effect of Inrush current on power transformers.
QUESTIONS: 1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When rated current is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A. a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the efficiency of this transformer at full load, 0.8 power factor lagging. c. Ifstandard open-circuit and tests were performed on this transformer, what would be the measured values of these tests? 2. The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformer tested at 50 Hz: Voltage (V) Current (A) Power (kW) LV winding with HV terminals open-circuited: 3810 9.86 8.14 HV winding with LV terminals short-circuited: 920 141 10.3 a. Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltage winding. b. Calculate the…
Q5: An electron drops from specific energy level to ground state (n=1) in hydrogen atom. The energy difference between these two levels is 12.75 eV. Calculate the initial state of the electron and 2 of the emitted radiation. (Ans: n¡ = 4, 972.54 Å) %3D
Find the elements of the equivalent circuit attributed to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuit are 200 volts and 400 volts, respectively, with a frequency of 50 Hz. The primary no-load current at the voltage of 200 volts is 0.7 amperes and the loss of the core is equal to 70 watts. The resistance and reactance of the primary are 3.2 ohms and 1.25 ohms, respectively. The resistance and reactance of the secondary are 0.6 ohm and 0.07 ohm, respectively. Draw the equivalent circle, showing the values of its elements.
1) A 12 kVA, 4400V/230V, 50 Hz single-phase transformer has 150 secondary turns. Determine (a) the primary and secondary current,(b) the number of primary turns, and (c) the maximum value of the flux.
A 36/240 V phase transformer, belonging to a phase measured from the no-load (idle) run and short-circuit test. values are given in the table below. High voltage by applying rated voltage to the low voltage winding (The winding ends were left unloaded and the results of the no-load test results were obtained. By applying nominal current to the high voltage windings, the low voltage windings were short-circuited, and the results of the short circuit test were obtained. In direct current test 1 V direct voltage is applied to the low voltage winding, and the transformer draws 500 A direct current. All equivalent Calculate the circuit elements as moved to the low voltage side. Idle run test: Voltage : 36V Power : 68W Current : 2,8A Short circuit test: Voltage : 15V Power : 325W Current : 42,2A
For given base voltage and base volt-ampere, the pu leakage impedance of a transformer is 'x'. What will be the pu leakage impedance of this transformer when the voltage and volt ampere bases are both doubled?
A 3.5 kV / 120V, 50 Hz, single phase transformer is to have an approximate e.m.f per turn of 33V and operate with a maximum flux density of 1.35T. Determine, (a) The number of primary and secondary turns. (b) The cross sectional area of the core.