portant values if needed for this question. (1) If a 86.1 g sample of the liquid 1-iodohexane has a volume of 59.8 mL, what is the density of the compound in g/mL? density = g/mL (2) The liquid 1-iodohexane is insoluble in water. If approximately equal volumes of water and 1-iodohexane were mixed in a separatory funnel, would the water layer end up on the top or on the bottom? The density of water is 1.0 g/mL. Submit Answer

portant values if needed for this question. (1) If a 86.1 g sample of the liquid 1-iodohexane has a volume of 59.8 mL, what is the density of the compound in g/mL? density = g/mL (2) The liquid 1-iodohexane is insoluble in water. If approximately equal volumes of water and 1-iodohexane were mixed in a separatory funnel, would the water layer end up on the top or on the bottom? The density of water is 1.0 g/mL. Submit Answer

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

What is the percent recovery if you started with 9.3 mL of benzaldehyde and ended with 4.1 g of benzaldehyde after distillation? Give 2 significant figures in your answer. Assume the density of benzaldehyde is 1.044.
What is the mass of glucose present? How many moles of glucose are there (three significant figures)? What is the mass of water present (in grams)? (Hint: Solution - Solute = Solvent) What is the molality of sucrose in water? What is the freezing point of the grapes (deg C)? What is the freezing point (deg C) if the molality of the glucose in water is 2.16 mol/kg?
Answer in scientific notation with the appropriate number of significant figures. For a laboratory experiment, you are provided with a stock solution of food dye. This is the solution from which you will prepare all of your standard solutions. The concentration of the stock solution will be approximately (7.5000x10^-5) mol/L. How many milliliters of this stock solution is needed to prepare 50.0 mL of a (1.50x10^-5) mol/L solution?
1. Several students performed this experiment without paying adequate attention to the details of the procedure. Briefly explain what effect each of the following procedural hanges would have on the size of the volume- to- temperature ratio calculated by the students. (a) One student failed to replenish the boiling water in the boiling- water bath as the flask was being heated. At the end of the 6 min of heating, the boiling water in the bath was only in contact with the lower portion of the flask. (b) Following the proper heating of the flask in the boiling water, a student removed the flask from the boiling- water bath but only partially immersed the flask in the ice-water bath during the cooling period. (c) A student neglected to close the pinch clamp before removing the flask from the boiling water bath and immersing it in the ice-water bath. (d) One student neglected to measure the volume of the flask before leaving the laboratory. Because the procedure called for a 125-mL…
Arrange the following volumes in order from largest to smallest. (2) 2.5 mL, 250 µL, 0.025 mL, 2.5 µL
A drug is supplied as a solution of 100. mg/mL. If 2.0 mL of this concentrated drug solution is diluted to a volume of 25.0 mL, how much of the diluted solution should be administered to supply a dose of 150 mg? (Use two types of problems in this problem.) 0.053 mL 8.0 mL 7.5 mL 19 mL 0.13 mL
A tank with a capacity of 74 liters, initially contains 20 kilograms of salt dissolved in 50 liters of water. Another solution, containing 3 kilograms of dissolved salt per liter, runs into the tank at 4 liters every minute and that the mixture (kept uniform by stirring) runs out of the tank at the rate of 1 liter per minute. What is the concentration of the solution in the tank at point of overflow? Intermediate values should be rounded only to two decimal places. Round off the final answer to two decimal places.
Question 1: Justin followed the procedure described in the lab handout to prepare a solution in which approximately 12 g of sugar was dissolved in enough water to yield 100.0 mL of solution. He recorded the following data on his data sheet:Mass of Empty Stoppered Flask (Column A) = 65.649 gMass of Sugar (Column B) = 12.674 gMass of Stoppered Flask with Solution (Column C) = 170.030 gWhat should Justin record as the mass of the solution (Column D) on his data sheet? You must Include the correct number of significant figures in your answer! Question 2: Use the data given in Question 1, and your answer to that question, to calculate the density of the sugar solution (Column E in the data table). When the volumetric flask is filled to the mark, it contains 100.0 mL of solution (i.e. the solution volume is known to 1 decimal place).You must include the correct number of significant figures in your answer!
How many milliliters of 25.0 mg/L stock solution must be added to a 25.00-mL volumetric flask to produce a 20.0 mg/L solution? Report your answer in decimal form (not scientific notation) with correct sig figs and including one space followed by your units.
A vial containing 500 mg of drug X powder for reconstitution is reconstituted with sterile water for injection. What is the displacement value in mL/g of drug X given that 8 mL sterile Water for Injection, BP is added to the powder to produce 10 mL solution?
Determine the moles of NaOH used for each substance for each trial
The percent mass per volume sugar concentration can be calculated using the following expression: % sugar () = 100 x g sugar total mL of the sample %3D What's the %sugar (m/v) concentration of a sugar standard solution that was made by adding 4.96 g of sugar to 288 mL of water? Question 2 Density is the ratio of the volume of a sample to its mass. density = mass volume What's the density of a 1.5 mL solution that weighs 1.16 grams?