pomy I. An overhead transmission line at a river crossing is supported from two towers at heights of 50 m and 100 m above the water level. The horizontal distance between the towers is 400 m. If the maximum allowable tension is 1800 kg and the conductor weighs 1 kg/m, find the clearance between the conductor and water at a point mid-way between the supports. 163-8 m]

pomy I. An overhead transmission line at a river crossing is supported from two towers at heights of 50 m and 100 m above the water level. The horizontal distance between the towers is 400 m. If the maximum allowable tension is 1800 kg and the conductor weighs 1 kg/m, find the clearance between the conductor and water at a point mid-way between the supports. 163-8 m]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5) Choose the correct answer with the explain: a) The maximum power transferred to the load is satisfied at, 1. ZL=0 2. ZL=00 3. ZL=Zo b) For a certain transmission lines, if l-50m and ta2-400nsec, then Vp will equal to: 1. 125*106 m/sec 2. 250*106 m/sec 3. 500*106 m/sec c) The minimum and maximum values of the reflection coefficients are, 1. O and 1 2. 0 and infinity 3. -1 and 1 d) For a certain transmission line, Zo=2002, l=200m. if I changes to 100m, then Zo will be: 1. 502. 2. 1002. 3. 2002.
Question 4
The Cost OF Single phase overhead feeder is OMR q Per KM(a is area of cross section in sq mm) and the intrest and depre Ciation Chargs onfeeder omical carrent density are 7Y. defermain to use for the most econor requiring Full load current of 27% of the 12 baisa is year. The Cost per unit ass ume resistance of Im lenahth length and I mm² secfion of Conductor as 1/32 find Current densi ty =?
In an overhead transmission line, if 'L' is the length of span in meters, 'w' is the weight of conductor per meter, and 'T' is the allowable tension in the conductor in kg, then the sag 'S; in meters is given as (a) wL²/8T (c) WL³/8T (b) WL²/4T (d) WL4/8T
Q: a transmission line conductor is supported by two same height towers at equal level from the top of each tower the clearance was 15.25 and Sı=2.25 , S2=20.25 the weight of conductor was 1 kg/m and the tension was 1800 kg and the length of span 360m Find the height of towers
The diameter of the overhead lines in the form of cylindrical conductors in a 300 kV three-phase transmission system is 20 mm.a) - How much distance should there be between two conductors using the maximum area calculation equations?Calculate. (Puncture peak strength of air is 30kV / cm.)b) - In this configuration, if the distance between phase conductors is 0m, at what voltage levelCalculate the discharge occurs?c) - Maximum electric field in the same configuration, for electrode distances to be 0mCalculate the value. If needed in calculations Ꜫ0 = 8.854x10-12 F / m)
An overhead line is supported between two towers which are at the same vertical height from the ground. The horizontal distance between the towers is 300m. If the conductor weight is 30N/m and the tension at the towers is 30kN, calculate i. the maximum conductor sag. ii. Find also the total length of the conductor.
The 84-meter-long conductor with a unit weight of q=0.7 kg/m was stretched on two poles at a horizontal distance of “a” from each other, and the deflection value was measured as f=15 meters. Accordingly, with the catenary method:a) Calculate the value of “a”b) Calculate the deflection value at a horizontal distance of 17 meters from the lowest point of the conductor to any pole.c) Calculate the resultant tension force (S) at the peaks.d) Calculate the angle that the direction of this force S makes with the horizontal axis at the apex.