5) Choose the correct answer with the explain:a) The maximum power transferred to the load is satisfied at,1. ZL=02. ZL=003. ZL=Zob) For a certain transmission lines, if l-50m and ta2-400nsec, then Vp willequal to:1. 125*106 m/sec2. 250*106 m/sec3. 500*106 m/secc) The minimum and maximum values of the reflection coefficients are,1. O and 12. 0 and infinity3. -1 and 1d) For a certain transmission line, Zo=2002, l=200m. if I changes to 100m,then Zo will be:1. 502.2. 1002.3. 2002.

Maximum power theorem: The condition of maximum power dissipation across the load is RL=Ro. That…

5) Choose the correct answer with the explain: a) The maximum power transferred to the load is satisfied at, 1. ZL=0 2. ZL=00 3. ZL=Zo b) For a certain transmission lines, if l=50m and ta2-400nsec, then Vp will equal to: 1. 125*106 m/sec 2. 250*106 m/sec 3. 500*106 m/sec

5) Choose the correct answer with the explain: a) The maximum power transferred to the load is satisfied at, 1. ZL=0 2. ZL=00 3. ZL=Zo b) For a certain transmission lines, if l=50m and ta2-400nsec, then Vp will equal to: 1. 125106 m/sec 2. 250106 m/sec 3. 500*106 m/sec

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vbase_zonel Sbase_zonel . * For the power system shown in Figure Q1b, calculate the per unit impedances of all components with given zone 1 voltage base 22kV and power base 100 MVA (for the system). = 22 kV = 100 MVA Generator: . YG₁ Zone 1 100 MVA 22 kV (0.1+ j0.5) pu 1 . E 1 T₁ YY Transformer 1: 100 MVA 25/130 kV (0.1+j0.5) pu Zone 2 L = (10+j100) S2 Figure Q1b. T₂ Zone 3 YA Transformer 2: 50 MVA 110/33 kV (0.1+j0.5) pu M₂Y Load (motor): ● 50 MVA . 33 kV (1+j0.5) pu
A high-voltage direct-current generating station delivers power to a city. The generator output voltage is Vo = 400 kV, the city is represented by resistance RL = 1749 ohms, and each wire of the transmission line round-trip between the station and city is represented by resistance RTL = 159 ohms. What percentage of total power supplied by the generating station is consumed by the transmission line? Vo RTL M RTL M RL (city)
QI/A: The per unit admittances are indicated at the diagram and the bus data are given in table as shown. Determine the voltage at bus 2 and reactive power at hus 3 after one iteration using suitable method. All values are in per unit. PL PG No. OL QG Angle Type 1.0 0 Slack *** 0 2 Load 0.15 0 ? 0 Gen. y=-j5 p.u y=-J2 p.u 3 3 8420 0.8 0 wwww 1.0 1.0 0.35 0 y=-32.5 p.u
d. Why do we need Transmission system in various power plants and vehicles?
In an overhead transmission line, if 'L' is the length of span in meters, 'w' is the weight of conductor per meter, and 'T' is the allowable tension in the conductor in kg, then the sag 'S; in meters is given as (a) wL²/8T (c) WL³/8T (b) WL²/4T (d) WL4/8T
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the apparent power supplied by the generator. The apparent power supplied by the generator is _____ VA.
Discuss the concept of islanding in power systems and the challenges associated with it.
Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and have the following characteristics: Area 1: R1 = 0.01 pu and D1 = 0.8 pu on a base of 1200 MVA Area 2: R2 = 0.02 pu and D2 = 1 pu on a base of 600 MVA The power flow direction on the tie line is from Area 1 to Area 2. Using a common base of 1000 MVA, what is the change in prime mover power (in MW) in Area 2 (APmech2) for a load increase of 125 MW in Area 1?
Q2: A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight meter. The capacitance in µF/km without effect -1 of ground is إجابتك The capacitance in µF/km with effect of -2 ground is
Power engineering book Mehta
Q2: The constants of a 275 KV transmission line are A = 0.8525° and B = 200275° 0/phase. Draw the circle diagram to determine the power and power angle at unity power factor that can be received if the voltage profile at each end is to be maintained at 275 KV. What type a rating of compensating equipment will be required if the load is 150 MW at unity power factor with same voltage profile. (5.5 mark)
For the system shown in figure, voltages V2, V3 and angles 82, 83 are calculated using Newton-Raphson method. shunt line charging admittances are neglected. All the values are given in per unit on 100MVA base. Calculate the complex power flows S12 and S32 in actual units. 1) Z12 = 0.01+ j0.02 Z3 = 0.02+ j0.04 PL G QL Slack bus V2 = 0.96L -1.67° V3 = 0.884 - 5.48° Vi=1.0/0° (estimated time to answer this question: 13 minutes)