POISSON'S RATIO, µ It is the ratio of indirect strain to direct strain Formulas: H= Eindirect /Egirect + Shearing Stress Where: E = linear strain = y/L Y = change in length L= original length PROBLEM 6: A 5 x 10 mm x 4m steel bar is subjected to axial force of 100 kN. E= 200 GPa and v = 0.3. ба. determine the change in its length. 6b. dimensions of its cross-section after determine the change in the

POISSON'S RATIO, µ It is the ratio of indirect strain to direct strain Formulas: H= Eindirect /Egirect + Shearing Stress Where: E = linear strain = y/L Y = change in length L= original length PROBLEM 6: A 5 x 10 mm x 4m steel bar is subjected to axial force of 100 kN. E= 200 GPa and v = 0.3. ба. determine the change in its length. 6b. dimensions of its cross-section after determine the change in the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 68 MPa, determine the principal stresses acting at the point. 114 MPa 66 MPa 157.9 MPa and -155.4 MPa 82.0 MPa and -83.7 MPa O 121.2 MPa and -138.0 MPa O 167.4 MPa and -98.1 MPa O 133.2 MPa and -131.2 MPa
Determine the shear strain xy at corners A, B, C, D if the plate in Figure 5 distorts as shown by the dashed lines. Consider small strain assumption. 3 mm 300 mm y D 4 mm 400 mm- 12 mm B A mm 8 mm $2 mm X
Plane AB is under pressure and Plane AB has an angle = 30 degrees to sigma = 50 nPa.a. Determine the equations used to calculate the normal and shear stress in the plane ABb. Draw a normal vector sketch on the plane AB and the angle formed between the normal vector andc. Calculate normal stress and shear stress in plane AB (Round up to 4 digits after comma)d. Plot the point normal stress and shear stress plane AB on the Mohr Diagram sketch.
Figure 1 shows the elastically deformed shape AB'C'D' of a thin plate subjected to plane stress conditions. The elasticity modulus and Poisson's ration are E=210 GPa and v=0.33 respectively. Determine the direction (angle 0) of the maximum shear stress on the point 0(0.5, 0.5). C'(1.09, 1.08) D'(0.01, 1.03) C(1.00, 1.00) D(0, 1) A(0, 0) O(0.5, 0.5) B(1, 0) B'(1.05, 0.06)
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 500 psi in size. (a) Determine the stresses o, Oy, and the magnitude of T,y and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). C y Answer: (a) σχ- psi Oy = psi Tyy = psi (b) Op1 = psi Op2 = psi Tmax in-plane psi
Determine the equivalent state of stress on an element if it is oriented 50° counterclockwise from the element shown. Assume that σ = -13 ksi and Txy = -19 ksi. Solve the problem using ox Mohr's circle. σχ F Part A Determine the normal stress ox'. Express your answer in kilopounds per square inch to three significant figures. ANSWER: = Tap image to zoom ksi Part B Determine the normal stress Øy'. Express your answer in kilopounds per square inch to three significant figures. ANSWER:
Problem example Example 7-5: The state of plane stress at a point with respect to the xy- axes is shown in the figure. Using Mohr's circle, determine (a) The principal stresses and principal planes and sketch the results. (b) The maximum shear stress. (c) The state of stress with respect to the x'y'-axes. 20 MPa (+) A 16 MPa 50° X 40 MPa (+) 1. Omax 3. Op 7-42
3= The state of strains at a point are defined as follows. Find X and Y such that the normal and tangantial component of the strain vector on a plane with normal unit vector of n=(n,n2,n3) is equal to En Et. 80 Y-50 [ε] = Y X 20 (*10 m/m) 50 4 n₁ n₂ n3 &*10 0.4 0.2 0.894 37.57 -50 20 En *10 28.58
The uniform forces U and P are applied to a plate with dimensions of 500mm x 400mm and a thickness of 10 mm as illustrated. Consider the linear elastic behavior, 200GPa Young's modulus, and 78GPa shear modulus. The plate is subjected to a uniform force U with an undetermined magnitude and direction and a uniform tensile force P=50KN. X 500 mm 400 mm A. What is force U, in kN, if deformation along y is zero? Is it a compressive or tensile force? B. What is the x-axis deformation, in mm? Is the dimension growing or shrinking?
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Calculate the shear strain, Yxy, at A. Also, calculate the average normal strain & along the x' axis. 800 mm 45% 45° 800 mm 5 mm
Your answer is partially correct. The strain components for a point in a body subjected to plane strain are ɛx = 820 µɛ, ɛ, = -360µɛ and yYxy = 804 prad. Using Mohr's circle, determine the principal strains (€p1 > Ep2), the maximum inplane shear strain yip, and the absolute maximum shear strain ymax at the point. Show the angle 0, (counterclockwise is positive, clockwise is negative), the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Answers: Ep1 = 942.81 με. Ep2 = -482.82 με. Yip = 1180 prad. Ymax = 1427.87 prad. 6,- 9.406