Poisson's Ratio is: a. The ratio of stress to strain in the elastic region. b. The ratio of transverse strain to axial strain. c. The ratio of maximum stress to average stress. d. The ratio of yield strength to allowable stress.

Poisson's Ratio is: a. The ratio of stress to strain in the elastic region. b. The ratio of transverse strain to axial strain. c. The ratio of maximum stress to average stress. d. The ratio of yield strength to allowable stress.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 12CQ

See similar textbooks

Related questions

Q: Q3 / An element in plane stress at the surface of a large machine is subjected to stresses shown…

A: Draw the state of stress diagram:-

Q: Find the stress distribution in the beam shown in the figure below A, E. I constant

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Size of grid square, Number of grid from origin to x about horizontal axis, Number of grid from…

Q: An elastic bar of length L, uniform cross-sectional area A, coefficient of thermal expansion a , and…

A: Solution; The axial stress diagram; σ varies with ∆T and does not depends upon the length of bar.

Q: Element in plane.stress the stresses are and g, = 97 MPa, g, = 76 MPa and T= 22 MPa. Determine the…

A: Radius of the circleR=(σx-σy2)2+τxy2R=(97-762)2+222R=24.38 MPA

Q: Which of the following is NOT TRUE in the elastic analysis of circular members under torsion? O…

A: A shaft is said to be in torsion when equal and opposite magnitudes of torques are applied at 2…

Q: Stress (MPa) 2000 Using the stress-strain results shown in the figure, determine the 0.2% offset…

A: Approach to solving the question:Identify the 0.2% offset yield strength from the stress-strain…

Q: The state of stress at a given point in a material component is = 120 MPa ; Oy ox = -80 MPa and t =…

Q: All of the following statements are correct except: a. Materials with higher modulus of elasticity,…

Q: Show the relationship between axial stress and strain to get the axial deformation

Q: Determine the Poisson's ratio v.

Q: The rectangular steel plate in the figure is forced by the forces given at the A and B points. a)…

Q: At a certain point in a structural member, there are perpendicular stresses 80 N/mm² and 20 N/mm²,…

A: Given data- Tensile perpendicular stresses given- σ1=80 N/mm2,σ2=20 N/mm2,Poisson's ratio μ=0.25, To…

Q: The state of stress at a point in a machine component is given by o, = 120 MPa, o, = 55 MPa, G = -85…

Concept explainers

Pressure and Stress

Question

Poisson's Ratio is:
a. The ratio of stress to strain in the elastic region.
b. The ratio of transverse strain to axial strain.
c. The ratio of maximum stress to average stress.
d. The ratio of yield strength to allowable stress.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
Shear modulus (G) is the ratio of a. Linear stress to lateral strain O b. Volumetric strain to linear strain c. Shear stress to shear strain O d. Linear stress to linear strain
Use Mohr circle
2.Discuss elastic region in a tensile test and shear test. It is always linear. What is engineering stress, strain ? Give Hooke's law, for tensile and shear deformation with corresponding modulus.
ProbleT = - An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and torque T = 300 N.m. (a) Determine the maximum shear, tensile, and compressive stresses in the bar, and show these stresses on sketches of properly oriented stress elements. (b) Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements. |d=40 mm T= 300 N-m
All of the following statements are correct except:a. Materials with higher modulus of elasticity, E are relatively weaker than those with lower E.b. Stress is proportional to strain within the elastic range.c. High carbon steel is stronger than concrete.d. In normal loading, the slope of the stress-strain curve is a material property called modulus of elasticity.The deflection of a beam is: A. Directly proportional to the modulus of elasticity and Moment of inertia B. Inversely proportional to the modulus of elasticity and moment of inertia C. Directly proportional to the load imposed and inversely to the length squared D. Inversely proportional to the weight and length
4
Which of the following best represents the distribution of the normal stress on the cross section of a linearly elastic member subjected to flexural loading? A.Uniform B.Parabolic C.Cubic D.Linear How does the flexural STRAIN on a fiber vary with respect to its distance from the neutral axis within elastic loading? A.Uniformly (it remains the same) B.Linearly decreases C.Exponentially increases D.Linearly increases Which of the following expressions best approximates the flexural bending stress at the neutral axis of a flexurally-loaded member with a rectangular cross section of depth 300mm, area 0.18m^2, and internal bending moment 2kN-m? a.0 MPa b.0.22 MPa c.0.44 MPa d.0.11 MPa Which of the following expressions is the maximum flexural bending stress of an L-meter beam with a constant rectangular cross section of width b and depth h subjected to uniform load Wo? Select one: OA 3 w L² 8 Ah о в. 3w,L² Ah O C. 3 w L² 2 Ah OD. 3 w L² 4 Ah
Bulk modulus is the ratio of a. shear stress to volumetric strain b. volumetric strain to shear stress c. compressive stress to volumetric strain d. volumetric strain to compressive stress
Please add a free body diagram
An element in plane stress is subjected to stresses o, = -8400 psi, ay = 1100 psi, and ty = 1700 psi (see figure). The material is aluminum with %3D modulus of elasticity E =10,000 ksi and Poisson's ratio v = 0.33. Determine the following quantities: (a) the strains for an element oriented at an angle 30 degrees, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements. Ty Txy Ox