Plotted measurements of the length of an object are shown below. Utilize the graph to get the average length, measurement error, and maximum and minimum values. GRAPH A Plot of Length Readings 7.05 6.9 6.85 6.8 6.75 6.6 6.55 Number of Trials Length of an Object (u)

Q: James was assigned by his teacher to measure the distance from their classroom to the school…

A: Given: Different measurements of distance made by James the from their classroom to the school…

Q: 3. Carry out each of the following conversions mg a. 450 µg / mL to mL b. 0.15 g/L to mg/mL 4. A…

A: According to Bartleby guidelines only one question is allowed to be solved at a time therefore I am…

Q: When calculating percent error are you supposed to round the true value to match your estimated…

A:

Q: Determine length CE for the similar triangles shown in Figure 1. E 25 m D A 10 m FIGURE 1 B 16 m

A: For similar triangles, corresponding sides are in the same ratio.

Q: 42. The density of aluminum is 2.7 g/cm³. What is the density in kilograms per cubic meter?

A: Density is Note:Find:Density in

Q: For each of the following descriptions of the volume of a cell, write a differential equation, find…

A: Given

Q: System

A: The SI unit is the international system of units that is used almost everywhere in the world. The SI…

Q: Data Table A. Temperature and Phase Changes Time (min) continued Time Temperature (°C) (min) 0…

A: 1. The graph using the data given is

Q: ad and the block's position is gi == xm cos(wt – ø), vhat is the ratio of the kinetic er

A: potential energy in SHM =(1/2)mw²x²

Q: 4 5 Answer: 6 7 8 0 1 2 3 4 5 6 7 8 9 10 Suppose that you measure the width of an object by using a…

A:

Q: Using dimensional analysis, check which of the following equations is or are correct. 1. a=v/t 2.…

A: Given  a=v/t density =mass/volume  distance d=1/2 at

Q: A member in your group writes a length measurement as 2.26 ± 0.2 . The first term, 2.26, is called…

A:

Q: What is fractional error or percent error?

A: Fractional error is the ratio of the value of error to the value of the quantity.

Q: Define the following term: SI units

A: The SI unit is also called an international system of units and they are used universally as a…

Q: Consider the relative sizes of the items listed in the table. In the column titled "measurement,"…

A: Given : A list of items. Asked to complete the table.

Q: * ?What is the final reading of micrometer shown in figure below 10 Made in D0

A: The above instrument is a screw gauge.  Pitch of the screw gauge =Distance moved by a screwNo.of…

Q: 13. Measure the size of your shoe using an inexpensive ruler. Walk 10 nose to end steps. Then, using…

A: Given, observation of measurement of size of your shoe using ruler, tape. To find, %difference…

Q: What is the correct way of writing si unit

A: It should be written in

Q: Below is the calculator result for the operations indicated. Enter the answer to the correct number…

A:

Q: Procedure 1. The following are the measurements of the waistline of a family member taken by 3…

A: Given:

Q: Suppose an observer measures the speed of an object and determines that it is moving at 6.13 m/s.…

A: only one question is allowed for one post still I help you with 9 questions. please post remaining…

Q: A student is measuring the length of a table for class. She measures the table multiple times with a…

A:

Q: If you were to plot E vs v on a log-log graph what would you expect the slope to be? The expected…

A: Given             E=mv2/2

Q: Draw a graph of log(y) vs log(t) with these values

A: Given data: logy logt -0.056 -0.38 0.20 -0.25 0.48 -0.11 0.73 0.017 0.81 0.057 0.93…

Q: If you were to plot F vs r on a log-log graph what would you expect the slope to be? The expected…

A: Expected relation between  F and r is given as  F=KQqr-2

Q: How to determine the error in measured (mass, volume) and calculated (density) quantities ?

A: Introduction - Error are inaccuracies in measurement of a physical quantity. They happen due to…

Q: Which of the following is a use of dimensional analysis? a) To check the dimensional correctness of…

A: To find: Which of the following is a use of dimensional analysis

Q: A gravel truck is weighed as it arrives at a construction site, and weighed again as it leaves,…

A: Given, The mass of loaded truck ml=21230±20kg The mass when the truck is left m=18880±50kg

Q: What should you do after obtaining a numerical answer when solving a problem?

A:

Q: A room measure 50, how many (cm2) does this represent. _____________.

A: The measured area of the room is given as, A=50 m2

Q: A (An) ______________ measurement is one in which systematic errors are small.

A: Systematic errors are the errors introduced due to the inaccuracy of the measurement. This error is…

Q: A popular car has a gas tank that holds a maximum of 14.5 gallons of fuel. What the size of tank in…

A:

Q: If you are to measure the length, width and thickness of a book, what measuring device will you use?…

A: According to question: For measuring the length, width and thickness of a book, I prefer Measuring…

Q: Why did you use 1/2 in the equation?

A: we need to find the torque on stick  torque=force X perpendicular distance

Q: Convert minutes to units in 10-minute increments.

A: To convert minutes into units ,      1 hours = 60 minutes . this implies ,                 1 min…

Q: A. QUANTITATIVE ANALYSIS: Write A if what is in column A is greater than in column B, B if column A…

A: Since you have been posted multiple questions. SO we are solving only first question for you. If you…

Q: Activity Oliver and Robin have different stride lengths and want to compare them. Oliver uses a…

A:

Q: It is observed that a height of child is growing 0.5 inch per 6 months. At the age of 6 years, if…

A: Here given that the height of a child grows 0.5 inch per 6 month.Again at the year of 6 the height…