A simplified model of a bipolar junction transistor is shown in below Figure. Determine the hparameters of this circuit.50 ΩVV₁ = h₁l1 +h12V₂12=h2111+h22 V2950 Ω0.1v• 10 ΚΩ

V1= h11I1+ h12V2I2= h21I1+ h22V2

Answered: plified model of a bipolar junction…

plified model of a bipolar junction transistor is shown in below Figure. Determine the h meters of this circuit. 50 92 M V V₁ = h₁₁I₁ + h₁2 V ₂ 12 = h₂1I1 +h22 V ₂ 950 Ω 0.1u 10 ΚΩ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please solve the marked question.
1. The diodes in the circuit below have FBV=1.0V. Draw the transfer function for V1 versus V2 when -10
Draw the small signal equivalent circuit of the following circuit. Note that C1 and C2 are large AC coupling capacitors. 5 VIO C1 RF Q1 C2 fem RL Vo
Analyze the clipper circuit in Figure Q2a below and hence sketch the output waveform for one complete cycle of the input.
Light-emitting diodes (LEDs) are diodes made with III-V compound semiconductor materials such as aluminum gallium arsenide (AlGaAs), aluminum indium gallium phosphide (AllnGaP) or indium gallium nitride (InGaN), instead of silicon. The LEDs emit light when the device is operated under forward bias. LEDs of different colors have different turn-on voltages VD(on). For example: Color VD(on) Red ~ 1.6 V Yellow ~ 1.7 V (a) Model these five LEDs with a simplified piecewise linear model. (b) A rule of thumb is that it takes about 1 mA of current to "light" an LED while~ 10 mA is needed for it to appear bright. Use the piecewise linear model for the LEDs, for the over-voltage indicator circuit to the right, find the values of Vin which will cause D₁ or D₂ to light (i.e. when ID1 or ID2 exceeds 1 mA). Green ~ 1.8 V Blue ~ 2.8 V loks o mu Vin Red LED Red LED White ~ 3.8 V + lov 21 D₁ D2 -10V o t Vout 오
Question 1 Find values of the intrinsic carrier concentration ni for silicon at 0°C. O 1.5 x 1010 carriers/cm3 O 1.5 x 109 carriers/cm3 O 1.5 x 109 carriers/cm2 O 5 x 109 carriers/cm3
1
(c) A 2400 V, 1000 KVA, 0.85 power factor (PF) lagging, 50 Hz six-poles, Y-connected synchronous generator has a synchronous reactance of 1.4 2 and an armature resistance of 0.15 2. At 50 Hz, its friction and windage losses are 25 kW, and its core losses are 15 kW. The field circuit has a DC voltage of 230 V, and the maximum IF is 10 A. The resistance of the field circuit is adjustable over the range from 20 to 200 £2. The Open Circuit Characteristic (OCC) of this generator is shown in Figure Q1(c). Calculate the internal generated voltage, EA of this machine at rated conditions. (i) (ii) (iii) Determine the required field current to make Vr equal to 2400 V when the generator is running at rated conditions. If this machine is operating at rated conditions, determine the input torque, TAPP that must be applied to the shaft of this generator.
PIV is the rating of a Diode when it is forward biased. [True / False] 15
Output voltage and Source volt = 5v Maximum LED current = 20 mA Apply Ohm's Law to Find R1.
Calculate the base current IB in uA when VCC=19V, VEE=-13V , RB=8193 ohm, RC=13724ohm, RE=14656ohm and B=153
A 100 kV, 50 Hz supply is fed to a rectifier ammeter (using a bridge rectifier) through a capacitor. The PMMC ammeter of the rectifier instruments reads 45 x 10-3 amp. What is the value of the capacitor? (a) 15.90 x 10-10 F (b) 15.90 x 10-12 F (c) 17.66 x 10-9 F (d) 17.66 x 10-11 F