Please show clear and complete solutions. Box the final answers. JK CD ← Answer: 0- D M L 10' A L E H L L B L F 6 panels at 6' K L Make a cut through JK, CJ, and CD. The free-body diagram of the section to the right of the cut is shown. The diagram assumes that all members of the truss are in tension. Identify the angle 9. C L G D L L E H F L L G

Q: 14 70

A: solution given consider the figure into three areas A1=area of rectangle =70x70=4900 mm2y1=distance…

Q: In the friction-free siphon shown in Fig. 20, what are the pressures of the water in the tube at…

A:

Q: ; An open-topped cylindrical tank contains water that is 80% of its overall height of 1.2 m. The…

A: As per guideline, first three parts have been answered. Please repost the remaining parts.

Q: PROBLEM 1 A 4.5-meter-steel column is made of a built-up T-section. The T-section is composed of…

A:

Q: , An open-topped tank with square bottom, 0.9 m on a side is 0.60 m high. It floats in water. A…

A:

Q: :A stone is projected vertically upward from the top of a 120m-high tower at a velocity of 36 m/s.…

A:

Q: A steel [E = 200 GPa] rod with a circular cross section is 12-m long. Determine the minimum diameter…

A: Given data in question  Load Span member length  Elongation  Elasticity modulus  To find out…

Q: need really fast pls

A: To find:- centroid from top flange

Q: 6. Seawater (sg = 1.03) enters a heat exchanger through a reducing bend connecting a 4-inch copper…

A: Calculate the force required to hold the bend in equilibrium.

Q: At a point on a streamline, the velocity is 3 m/s and the radius of curvature is 9 m. If the rate of…

A: Given data- A point on a streamline- Velocity =3 m/s, Radius of curvature R=9 m, Rate of increase of…

Q: Choose the letter of the answer. The external distance of a simple curve is 15m and has a central…

A:

Q: Q1 part b o

A: Given data weight of the gate=50kN width=2m Draw the figure

Q: If the beam has an overall depth of 758 mm, 4-ø22 mm tension bars and the distance of the neutral…

A:

Q: 13. PC elev = 200.00 G1 = -3% G2 = +2% low elevation on curve is 184.00 Find L. (a) 7 sta. (b) 12…

A:

Q: Show fbd and comp sol. The uniform rod weighs 420 lb. and has its center of gravity at G. Determine…

A:

Q: SITUATION 1 Verify the adequacy of column CB,. part of a sway frame structure, to carry the loads…

A: Factored weight on column CB (LRFD) = Pu = 1.2*P(DL) + 1.6*P(LL) = 1.2*40+1.6*125 = 248 kN.   Length…

Q: Two lbs of water vapor in a piston-cylinder assembly expands at a constant pressure of 300 lb/in²…

A:

Q: CONJUGATE BEAM METHOD FOR BEAMDEFLECTION For the beams below, determine the magnitude of the maximum…

A:

Q: If the jam density on a road designed for a free mean speed of 75 km/h is 100 vehicles/km, then the…

A: Given data,  Vsf= 75km/h  Kjam= 100vehicles/km  Capacity flow= ?

Q: Q.1) For the plate shown in figure, determine the forces in three ropes if the plate weighs 1.6 kN.…

A: Solution:

Q: Show fbd and comp sol. Identify the load P required to hold bar AB in a horizontal position on the…

A:

Q: Find the following PROBLEM 1 internal forces at point E Beams AB and CD are both 100mm x 100mm in…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: USE METHOD OF SECTIONS, SHOW COMPLETE SOLUTION WITH FBD: ompute the force in member GM of the loaded…

A: To find force in member GM

Q: SITUATION 2 A 7-m simply-supported floor beam, made of ASTM A36 steel (Fy = 250 MPa). W18x50…

A:

Q: -) The gate shown below rests on a Sinooth floor at A and is hinged at B. Neglecting its weight,…

A:

Q: Determine the frictional force created between the 490.50N wOoden box and the ground if P = 0.200…

A:

Q: Q.3 A steel beam has the cross-section shown in Figure Q.3(a) and the steel has a yield stress of…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: Determine the slenderness ratio of a 5-m steel column, fixed support at both ends, having the cross…

A: We will find radius of gyration and effective length.

Q: On the soil profile shown, how high should the GWT rise/fall so that the effective stress at C is…

A:

Q: V Discuss strain hardening covering its significance in the context of plastic deformation and…

A: Strain hardening:- Strain hardening is generally defined as heating at a relatively low temperature…

Q: D. A cartesian coordinates of a point moving in the xy plane are x = 2Ut + 4t2 m and y = 10 t3 m.…

A:

Q: B. The motion of the particle is defined by the relation x 2t - 15t 24t + 8 where x is expressed in…

A: As given in question, X=2t3-15t2+24t+8 on differentiation with respect to t ,we get-…

Q: D45 300 N/m -15mt15m+15m+15m- The cable BCD is attached to the shown beam through a frictionless…

A:

Q: Question 1 A beam of circular cross soction is 22 cm in diameter. It is simply supported at each end…

A:

Q: 1. Two tanks A and B have 70 m difference in water levels, and are connected by a pipe 0.25 m…

A:

Q: Determine the moment at B for the beams shown using the three-moment equation. Express your answer…

A: Determine the moment at support-B of the beam using Three Moment Equation.

Q: Calculate the size and number of slow sand filter units to serve a population of 10,000 with an…

A:

Q: Use virtual method and Solve for the deflection @ B Slope @ A Slope @ C

A:

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.