Express the answers in solution in 2 decimal places. Thank you Please refer to the figure shown below. If P is equal to 6,720 lb., and ifall the rods have a cross-sectional area to be 0.4 sq. in. Explain whythe set-up will fail or will not fail if the allowable stresses in Steel is120MP%; 90MPa in Alumimun; and 100Mpa in Bronze. As the civilengineer of the project, if the set-up fails, provide a recommendationto prevent the failure to occur. Show your solutions to support yourrecommendation.4PSteelBronzeAluminum| P2 ft3 ft2.5 ft

Answered: Image /qna-images/answer/63dad036-a2c3-4daf-8988-1b29712031a6.jpg

Please refer to the figure shown below. IfP is equal to 6,720 lb., and if all the rods have a cross-sectional area to be 0.4 sq. in. Explain why the set-up will fail or will not fail if the allowable stresses in Steel is 120MPA; 90MPa in Alumimun; and 100Mpa in Bronze. As the civil engineer of the project, if the set-up fails, provide a recommendation to prevent the failure to occur. Show your solutions to support your recommendation. 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft

Please refer to the figure shown below. IfP is equal to 6,720 lb., and if all the rods have a cross-sectional area to be 0.4 sq. in. Explain why the set-up will fail or will not fail if the allowable stresses in Steel is 120MPA; 90MPa in Alumimun; and 100Mpa in Bronze. As the civil engineer of the project, if the set-up fails, provide a recommendation to prevent the failure to occur. Show your solutions to support your recommendation. 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pls. Answer it completely
Fill in the word or numerical value in the blanks. Show your solution in a short size bondpaper.
Instructions: Convert. Show complete solutions to get full credit. 1. 7658 mil to radians
PLEASE WRITE YOUR COMPLETE SOLUTION AND BOX THE FINAL ANSWER. THANK YOU.
No copy paste from other sources. Write your own answer! Q. Describe the importance of penetration testing?
Use 3 decimal places only in all of your rounding off.
ID NUMBER - 20-3994-175 *PLEASE ANSWER ALL THE QUESTIONS . Pls Put the number in every answer Don't Round Off answers unless it is already the final answer Final Answer must be up to 3 Decimal Places only
Using the section method (the average end area method), determine the required volume of the cuts and fills for a new road. The cuts and fills for each station are shown in Table below. Express your answer in cubic yards. Station 1+00 1+50 2+00 2+50 3+00 3+40 Cut (sf) 340 115 120 80 250 0 Fill (sf) 20 80 100 O 300 400 Complete the table using either Excel or hand calculation and send it to the instructor via Folio email.
MY ID NO. 20 -3994 -175 PLEASE INDICATE THE NUMBER IN EVERY ANSWER FINAL ANSWERS MUST BE UP TO 3 DECIMAL PLACES ONLY
Instructions: Convert. Show complete solutions to get full credit. 1. 75 deg 25 min 30 sec to degree decimal
Show your design, plan, estimates of materials of the following plumbing system: -Sprinkler System -Sanitary System -Provide a diagram for the kitchen and comfort room. Create a table to organize your answer.
Thanks for your help, the question is asking to use mohr's circle