Please look for Vi (letter J)

Q: F. Use this graphic for Question 6. R1 A 2 kQ R2 5 kQ B vs 35 V 34 kQ R3 3 ko

A:

Q: Ic = ICA + ICB 16/270° - 24/-30° = 21.2/190.9°

A: Given , IC=ICA+ICB ICA=16<270° A ICB=-24<-30° A We need to calculate Ic

Q: Given T2 300, what is n? ↑ 6430° A 4430° A O 150 O 450 O 200 O 600

A:

Q: Q/ Find Reg between a and b ?

A:

Q: What is VA? 12√ E 12 VA 1856 Tor лол 10-2

A: Introduction: Kirchhoff's current…

Q: The maximum current carrying capacity for a 25 sq. mm UG cable is 100 and above O 0-80 O 81-90 O…

A: In this question , we will find maximum current carrying capacity of cable..

Q: 2. Find 1₁, 12 and 13. 1522 M 30V +1 52 SI₁ W 12 30 18 12_2 > 13 302 W 2012 2052

A: In this question we need to find the current I1 , I2 and I3 shown in the given circuit.

Q: 8(-4t) - O 8(t) O-45 (t) • 15 (e) 2-6(4) O 45 (t) O-8 (t)

A: The solution is given below

Q: Find Rth for the following circuit. 4V 50 www 150 www 1002 www 80 120 www 6V

A: For calculating thevenin resistance, voltage source is short circuited and current source is open…

Q: x(t) -1 o' Figure Q1(a)

A:

Q: b 3Ω 10 Ω d

A:

Q: 2- State the benefit of increasing the width of the address bus

A: There are two main types of buses in a microprocessor. These are address bus and data bus.

Q: Current io is equal to a 0.5i, 4Ω ЗА O 24A O 12A O 4A О 6А ww

A:

Q: 2. Determine the total impedance and the total current. 4n -jan H 3n j4n 12010°v (E

A: According to the question we have to find the value of the total current and total impedance.

Q: Quèstion 14 The base 10 system has elements from 0 to 10 0 to 16 0 to 8 None of the other answers

A:

Q: Can you please circle ⭕️ the answer of questions C and F BECAUSE ITS

A: Need to find the root locus on the real axis and the angle of departure.

Q: what is the substation single line

A: SUBSTATION SINGLE LINE DIAGRAM: A single-line diagram, often known as an SLD, is an electric…

Q: Evaluate the following complex numbers. Your final answer should be in polar format, i.e. rzq. Make…

A:

Q: choose the correct answer.

A: In this question we will find unknown current using kCL....

Q: Q1 Find the total current SA Find It

A: PRESENCE OF SOURCE: In the presence of sources all the passive elements which are R, L and C always…

Q: get the even and odd part of the figure 10.

A: In this question, we need to determine the even and odd signals of the given signal.

Q: Determine current I, using mesh analysis j12n In jIon 80/90°V

A: According to the question we have to find the value of In.

Q: Q1) Find Io in the given diagram: a) Using software program (Multisim or Pench) Theoretically b) σον…

A:

Q: it R1 R3 1

A:

Q: Determine the number of groups in this K-Map: CD 00 o1 11 10 AB 00 0 o o 0 01 0 110 110 11o 10 0 o o…

A: The K-Map is used for additional simplification in the circuit. This additional simplification…

Q: Sulve for X 2/3 -4/+5=27 +5 =27

A:

Q: Is N1 (N2 = 140 turns) 42 0.66 A 84 1.285 A 112 1.645 A 140 1.917 A

A: The given table of the secondary short circuit current and the number of turns in the primary coil…

Q: Show graphical convolution for the following pair of signals x[n) Ili.. Figure 1 2 3 -2 -10 12 ...…

A:

Q: 2X dx (メ-5)5

A: The integral simplified is given as: where C is constant of integration.

Q: Im not sure if i am correct. I dont have any way to check my answers. Does this circuit not work…

A: The circuit can be analyzed by verifying the elements in the circuit that are open-circuited. The…

Q: 5. Using nodal analysis, find V₁, V₂ and V₂ 6A ↑ V₁ M 92 M 452 8A 352 V2 42 62 W √3 782 9 v

A: In this question we need to find the voltage V1 , V2 and V3 .

Q: To what value must Cext be changed in the figure to achieve a frequency of 25 kHz? Consider one…

A:

Q: L. 6 (t) dt

A:

Q: 6. R=_kQ |= 4 mA E= 6 V

A:

Q: The multiplying power of the shunt of a millimeter is 8. If the circuit current is 200 mA, then…

A: Given, The multiplying power of the shunt of a millimeter, m=8. The circuit current, I=200 mA. The…

Q: 2552 man 2552 wwwwww 2552 wwwwwww 25.22 wwwww 2552 2552 DIA

A: Given Data:A DC resistive circuit with,Voltage source Current source To Find:The current  by the…

Q: L 45° XV = 10 m/s 1 = 0.25 m B = 0.25 T into the page Figure 2 (b) XE X

A:

Q: Quèstion 5 The number 458 in base 10 has the same number of digits in base 8 has smaller number of…

A: Solve as below

Q: Consider the following tree Identify leaf nodes Identify internal node What is height of T

A:

Q: RefeR to the ciecuit below R- GiveN Cind I,,Iz, * 22052 RT IT RT

A: To calculate total resistance RT, IT, I1, and I2

Motor Load, Torque, and Power Quality Requirement

An electric motor is a gadget that changes electrical energy into mechanical energy over to follow up on a mechanical burden. The weight set on the motor because of this mechanical movement is known as motor load. Appropriately matching the motor burden to the engine is vital to forestall harm to the engine or wasteful and unnecessary expensive activity. Engines perform such undertakings as moving a thing starting with one spot then onto the next, cutting it, changing its shape, etc. The motors might be evaluated as far as a few variables including power yield, voltage, current, and temperature. Harm to an engine might happen when it is worked under over the top engine load contrasted with its appraised limit.