Pitot tube head Tube several metres long shown in cross- section Pitot tube head (1) State one factor that would have to be taken into consideration when choosing where to position the Pitot tube head on the exterior of an aircraft if the true airspeed is to be indicated. (ii) Would water be a suitable liquid for the manometer if airspeeds of up to 600 km h- are to be indicated in the cockpit of an aircraft? Justify your answer.

Pitot tube head Tube several metres long shown in cross- section Pitot tube head (1) State one factor that would have to be taken into consideration when choosing where to position the Pitot tube head on the exterior of an aircraft if the true airspeed is to be indicated. (ii) Would water be a suitable liquid for the manometer if airspeeds of up to 600 km h- are to be indicated in the cockpit of an aircraft? Justify your answer.

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter5: Displacement And Force In Two Dimensions

Section: Chapter Questions

Problem 86A

See similar textbooks

Similar questions

I want a quick solution, please fast, I don't have enough time Gas guns are used to investigate the properties of materi- als subjected to high-velocity impacts. A projectile is accelerated through the barrel of the gun by gas at high pressure. Assume that the acceleration of the projectile in m/s² is given by a = c/s, where s is the position of the projectile in the barrel in meters and c is a constant that depends on the initial gas pressure behind the projectile. The projectile starts from rest at s = 1.5 m and acceler- ates until it reaches the end of the barrel at s = 3 m. Determine the value of the constant c necessary for the projectile to leave the barrel with a velocity of 200 m/s.
An open top tank half filled with water is to be transported constant acceleration. The dimensions of the tank are 1 m x 0.5 m x 0.5m, with the 1.0 m side parallel to the direction of motion. on a straight, horizontal road with a 1- Find the minimum acceleration of the tank at which the liquid will start to spill 2- What is the slope of the free surface of the liquid when the liquid starts to spill? 3- How would you show if there would form a dry spot under the above conditions? 0.5 m Water .0 m X
The average density of the Sun is on the order 103kg/m3 . (a) Estimate the diameter of the Sun. (b) Given that the Sun subtends at an angle of about half a degree in the sky, estimate its distance from Earth.
Stokes’ law describes sedimentation of particles in liquids and can be used to measure viscosity. Particles in liquids achieve terminal velocity quickly. One can measure the time it takes for a particle to fall a certain distance and then use Stokes’ law to calculate the viscosity of the liquid. Suppose a steel ball bearing (density 7.8103kg/m3 , diameter 3.0 mm) is dropped in a container of motor oil. It takes 12 s to fall a distance of 0.60 m. Calculate the viscosity of the oil.
A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be following figure). There is a spout located 0.15 m from the bottom of tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spat is As=7.0104m2 . (a) What is the velocity of the water as it leaves the spout? (b) If the opening of the spout is located 1.5 m above the grand, how far from be pout does water hit the floor? Ignore friction and dissipative forces.
Fill in the blanks. The engine room of a freighter is on fire. A fire-fighting tugboat has drawn along side and is directing a stream of water to go into the stacks of the freighter. If the speed of water jet is 20 m/sec, what angle a is needed to accomplish the task. 9 m Freighter tugboat 12 m-
Hi so here is a question we have and here is the answer for it, i understand everything up until the circled part i am really stuck there so if you could just use alot of words when you explain it because our professor just puts the equation in without explaining it so please explain it as much as you can because i really dont understand it i would really appreciate it. Thank you
I am stuck on 4a
Needs Complete solution with 100 % % accuracy don't use chat gpt or ai plz plz plz plz.
9
Main Menu Contents Grades Course Contents » Problem Set #7 (due Mon 11/14) » Water jet Timer Notes Evaluate A jet of water squirts out horizontally from a hole near the bottom of the tank, as seen in the figure. 200 у X Assume that x = 1.36 m and y = 1.84 m. What is the speed of the water coming out of the hole? 2.22 m/s You are correct. Your receipt no. is 157-8046 Previous Tries If the hole has a diameter of 3.18 mm, then what is the height, h, of the water level in the tank? .2446m Submit Answer Incorrect. Tries 1/12 Previous Tries Post Discussion Feedback Print Send Feedback
A bricklayer hits a screw with a hammer and drives it into a ceiling. If the hammer hits the nail with three times the speed, how much deeper will the nail be driven?... Please explain MCQ choice (with calculations where needed) in the Rationale section! O A. four times deeper O B. nine times deeper. C. three times deeper ) D. the same depth