pipe with an outside diameter of 2.7 inches. insulate with a 2 inches. layer of asbestos (ka = 0.396 btu-in./hr-ft-F), followed by a layer of cork 1.5 inches. thick (kc = 0.30 btu-in/hrft-F). if the temperature of the outer surface of the cork is 91 F, calculate the heat lost per 100 ft of insulate pipe. The temp of the inner surface of the pipe is 275 F.

pipe with an outside diameter of 2.7 inches. insulate with a 2 inches. layer of asbestos (ka = 0.396 btu-in./hr-ft-F), followed by a layer of cork 1.5 inches. thick (kc = 0.30 btu-in/hrft-F). if the temperature of the outer surface of the cork is 91 F, calculate the heat lost per 100 ft of insulate pipe. The temp of the inner surface of the pipe is 275 F.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please help me solve this problem
Exercise 4.6.2 An insulation system around a cylindrical pipe consists of two different lay- ers. The first layer immediately on the outer surface of the pipe is made of glass wool and the second one is constructed using plaster of Paris. The cylinder diameter is 10 cm and each insulating layer is 1 cm thick. The thermal conductivity of the glass wool is 0.04 W/m°C and that of the plaster is 0.06 W/m °C. The cylinder carries hot oil at a temperature of 92°C, and the atmospheric temperature outside is 15°C. If the heat transfer coefficient from the outer surface of the insulation to the atmosphere is 15 W/m- C, calculate the temperature at the interface between the two insulating materials and on the outer surface.
Some help please (How do I go about this? TIA)...Determine the rate of heat loss per square foot through thr wall of your home if the home is heated to 70F when the outside temperature of -10F. Assume the fiberglass insulation has the same properties as silica glass fiber.
Two flat 1m x 2m panels are spaced 3m apart. The top panel is exposed to the sun and is currently 200oC. The bottom panel is not exposed to the sun. The panels have an emissivity of 0.3. a) If the bottom panel is absorbing 200W of thermal radiation, what is the temperature of the bottom panel? b) If the bottom panel is chilled to −60oC, how much radiation does it absorb?
6. Make a diagram and show the step-by-step process. Do not use shortcut methods. Make it as detailed as it can be. Encode (not hand-written)!
%^0 |. دردشة هندسة النفط/مسائي A composite wall consisting of five series layers of materials with different properties. Layer thickness, thermal conductivity of the layers and temperatures are shown on the figure. Based on Fourier's law for conduction, answer the following questions. 1. What are the main assumptions? 2. Drive an equation to calculate the heat transfer rate through the Composite wall? 3. Draw the themal circuit through composite wall? 4. What are the value Ti? 5. What are the value Tj? 6. What are the value Tr? Givens: KA = 2 W/m. °C K= 1 W/m.°C K= 5 W/m. °C Kp= 4 W/m, °C 100°C Ti 25°C Tj Tr A B D -2cm e 6 cm 4 cm 4cm إضافة وصف...
. thermodynamics- A platinum resistance thermometer has a resistance of 5 ohm at 0°C and 2.5 ohm at 100°C Calculate the temperature when the resistance indicated is 10 ohm.
An office space of 14 ft x114 ft x12 ft height. The heat loss through roof is (5131.3 Btuh) if Tb.l.=70 F, To= 5 F , and Uwall=0.35 Btu/hr.ft2.F * O True O False
In a glass plant in Cavite, a furnace has fire-brick walls made up of the following two materials in series : Non-corrosive brick as inner layer (material 1) Clay brick as outer layer (material 2) Thickness 4.5 inches 8 inches Thermal conductivity k1 k2 The temperature inside the furnace (inside wall surface of the non-corrosive brick) is found to be 1105 oF while the outside temperature (outside wall surface of clay brick) is 365 oF. This is not the desired temperature inside the furnace so engineers thought of lagging the furnace walls with another material to reduce heat loss. The additional lagging material consists of magnesia layer which is 2 inches thick and has a thermal conductivity of 0.04 Btu /h.ft.oF. During a test run on the furnace with the magnesia lagging material now, new temperature readings were recorded : Point of measurement Temperature reading Inside furnace (inside wall surface of non-corrosive brick 1355 oF Interface between…
A furnace wall is to be designed to transmit a maximum heat flux of 220 Btu/hr.ft of wall area. The inside and outside wall temperatures are to be 2200 • F and 320 ° F. Determine the most economical arrangement of bricks measuring (9 in x 4; in x 3 in). If they are made from materials one with ak of 0.44 Btu/hr. ft. ° F and maximum usable temperature of 1700 ° F and other with a k of 0.94 Btu/hr. ft. ° F and a maximum usable temperature of 2400 ° F. Bricks made of each material cost the same amount and may be laid in any manner (but bricks must remain intact, i.e., no partial bricks). After you answer the question, determine the percent increase in heat flux if there are two -in.-diameter steel bolts extending through the wall per square foot of wall are. (k of steel = 22 Btu/hr. ft. F)|
what id correct ans
A heating element made of tungsten wire connected to a large battery that has negligible internal resistance. When the heating element reaches 80.0°C, it consumes electrical energy at a rate of 480 W. Assume that the temperature coefficient of resistivity has the value given in Table 25.2 in the textbook and that it is constant over the temperature range in this problem. In the equation R(T) = Ro [1 + a(T - To)] take To to be 20.0°C. Part A What is its power consumption when the temperature of the heating element is 110.0°C? Express your answer with the appropriate units. P = Submit Value Provide Feedback Request Answer Units ?