Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 13 mm and an allowable normal stress of 95 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 6 mm, and an allowable normal stress of 125 MPa. Assume x₁ = 2.7 m, x₂ = 1.6 m, and y₁ = 4.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B A (1) Y₁ Answer: Pmax i P C kN

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 13 mm and an allowable normal stress of 95 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 6 mm, and an allowable normal stress of 125 MPa. Assume x₁ = 2.7 m, x₂ = 1.6 m, and y₁ = 4.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B A (1) Y₁ Answer: Pmax i P C kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250…

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 40 kN. Assume that a = 300 mm,…

Q: The solid 1.85-in-diameter rod is subjected to a uniform axial distributed loading along its length…

A: We will calculate effective load at each section.

Q: Each of the four vertical links has an 8 X 36-mm uniform rectan- gular cross section, and each of…

Q: (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft

A: Given figure shows a copper pipe subject to uniformly distributed torque. It is required to find…

Q: The copper pipe [G = 5,000 ksi] has an outside diameter of 3.750 in. and a wall thickness of 0.250…

Q: A 1600-lb in. couple is applied to a wooden beam, of rectang section 1.5 by 3.5 in., in a plane…

Q: Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm •…

A: Given data Diameter of hole (do) = 2cm = 20 mm Width of plate (B) = 6 cm = 60 mm Un-axial tension…

Q: The solid 1.15-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: Two steel [E = 30,100 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe…

Q: A bar of the rectangular cross-section is 100mm thick by 50mm broad and carries an axial compressive…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: a B C

Q: A 0.2 in. 4 in. 2 in. В D |- – 3 in. + 2 in.→ P=6 kips В Find the average normal & stress on a-a.…

Q: The copper pipe [G= 8,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.125…

A: Given data, Copper pipe , G = 8000 ksi Outside diameter = 3.875 in Wall thickness = 0.125 in UD…

Q: in. The pipe is subjected to a uniformly distributed torque of t = 63 lb-ft/ft along its entire…

A: Given:Uniformly distributed torque, t=63 lb-ft/ft…

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.500 in. and a wall thickness of 0.250…

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250…

A: Use formula of Torsion Calculate maximum torque

Q: Question 6 of 15 The plate of thickness, t = 5 mm, is loaded with the following stress; o, =100 MPa,…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: Determine the maximum stress of the plate.

A: Given, Determine the maximum stress of the plate. Rivet hole diameter.d= 2 cm Width,b= 6 cm…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: The rectangular bar has a width of w= 2.75 in. and a thickness of t = 2.00 in. The normal stress on…

A: Given : W = 2/75 in. t = 2.00 in Normal stress on plane AB of the rectangular block is 6ksi

Q: Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm •…

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250…

Q: Determine the maximum stress of the plate. • rivet hole diameter= 2 cm • width of the plate= 6 cm •…

Q: e pins are 1 cm in diameter and are made of 304 stainless steel. A distributed load of 200 N/m is…

A: Given:- two rigid bars with a 5cm x 5cm section A-36 steel. the pins are 1 cm in diameter a 304…

Q: The copper pipe shown in the figure has an outside diameter of 3.625 in. and a wall thickness of…

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

Q: Two steel [E = 29,400 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe…

Q: Question 1 of 5 /20 E View Policies Current Attempt in Progress The solid 1.05-in-diameter rod is…

Q: Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load P at…

A: Given: Tie rodDiameter = 12 mmAllowable normal stress = 65 MPaPipe 2Outer diameter = 46 mmWall…

Q: A solid 2.40 in. diameter shaft is subjected to a torque of T = 330 lb-ft and an axial load of P =…

Q: The solid 1.25-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial…

Q: member with 0.2-in. wall thickness (3), cach supports an axial tensile load of 5 ki (a) Determine…

A: for easier calculations first all units are converted in to SI and for simplicity again convered…

Q: The copper pipe [G = 5,000 ksi] has an outside diameter of 3.750 in. and a wall thickness of 0.250…

Concept explainers

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.

Question

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a
diameter of 13 mm and an allowable normal stress of 95 MPa. Pipe (2) has an outside diameter of 58 mm, a wall
thickness of 6 mm, and an allowable normal stress of 125 MPa. Assume x₁ = 2.7 m, x₂ = 1.6 m, and y₁ = 4.0 m.
Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable
normal stress.
Y₁
B
A
(1)
Answer: Pmax i
P
C
KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 32 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 90 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure. P Support Plate Rod Answer: Pmax i Hole diameter D Head KN
Two steel [E = 29,500 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.500 in. and a wall thickness of 0.283 in. Pipe (2) has an outside diameter of 4.375 in. and a wall thickness of 0.204 in. Assume L₁= 15 ft and L₂= 25 ft. If the normal stress in each steel pipe must be limited to 18 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ Answers: (a) (b) Pmax VB= (1) = i i C B kips in.
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
A square bar AB with an allowable stress of 32 MPa is attached to a hollow tube BC. Compute the inside diameter of the hollow tube BC if the allowable stress is limited to 220 MPa. P. A B Cross Section of AB Cross Section of BC 50 mm ODI s0 mm 50 mm
The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown, determine the shear stress developed at points A and B. These points lie on the pipe’s outer surface. Sketch the shear stress on volume elements located at A and B. . The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and it is subjected to the uniformly distributed torque along its entire length, determine the absolute maximum shear stress in the pipe. Discuss the validity of this result.
Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.
10. An Assembly shown below whereas a link BD consists of a bar with 1 in. wide and 1/2 in. thick. Considering that each pin has a 3/8 -in. diameter, Find the maximum value of the average normal stress in link BD given the conditions: (a) O = 0, (b) 0 = 900. 4 kips .6 in. 12 in. 30° D
a)jj holiow steel tube jsed in a roof structure has an outer diameter, d; = 104 mm and inner diameter, dz = 82 mm. The length of the tube is given by L = 2.75 m and has shear modulus, G = 28 GPa. If the tube is twisted in pure torsion by torques acting at the ends, distinguish the angle of twist when the maximum shear stress, Tmax = 48 MPa.
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.125 in. and a wall thickness of 0.286 in. Pipe (2) has an outside diameter of 4.000 in. and a wall thickness of 0.209 in. Assume L₁ = 13 ft and L₂= 21 ft. If the normal stress in each steel pipe must be limited to 24 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ Answers: (a) Pmax= (b) VB= (2) (1) tel i tel P C B kips in.
a.)For the given figure, determine the normal stress in MPa at segment AB, Cross-section of AB is 1500mm2. b.)Determine the normal stress in MPa at segment BC. Cross-section of BC is 2000mm2. c.)Determine the normal stress in MPa at segment CD, Cross-section of CD is 1200mm2.
show steps At point (A)