ー>コ>Dinmy= 316.229- The diagràm below represents the first three stages of a typical AM or FM receiver. Findthe following quantities.ngalPorA Pzreciver7attenuatorP-1 pWRFAmplifierAF=100MixerP2IF AmplifierAp=10,000-17Apz=0.2outpico watts-12a) Arand AT dB-b) Ap1,aB, Ap2,dB and Ap2,dB-c) P1, Pzand Pout.xFin d) Pin,dBm, P1aBm, P2,aBm and Pout,dBminPw= 1XI0 wconvertion to Bm

Note: As per the policy we can solve only 3 subparts of a question, please re-upload the remaining…

Piomwミ S6.22 9- The diagram below represents the first three stages of a typical AM or FM receiver. Find the following quantities. Por AP al reciver P3 yattenuator P=1 pW RFAmplifier A=100 Mixer P2 IF Amplifier Ap=10,000 ー17 Ap=0.2 %3D ut a) Arand AT,dB. b) Ap1,aB, Ap2,dB and Ap2,dB. c) P1, Pzand Pout. pico watts -12 Pw= 1XI0u Pw=1x10 lin d) Pin,dBms PaBm, Paapm and Pur aem Convertion to Bm

Piomwミ S6.22 9- The diagram below represents the first three stages of a typical AM or FM receiver. Find the following quantities. Por AP al reciver P3 yattenuator P=1 pW RFAmplifier A=100 Mixer P2 IF Amplifier Ap=10,000 ー17 Ap=0.2 %3D ut a) Arand AT,dB. b) Ap1,aB, Ap2,dB and Ap2,dB. c) P1, Pzand Pout. pico watts -12 Pw= 1XI0u Pw=1x10 lin d) Pin,dBms PaBm, Paapm and Pur aem Convertion to Bm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ASAP It is a type of diode where it operates as a variable resistor when heated. Your answer What is the modulation index in ideal condition of AM. Your answer A form of AM where a sideband is filtered after its carrier is eliminated. Your answer What is the form of AM that used to transmit video signals of the TV system? Your answer It is a circuit in the superheterodyne receiver that adds and subtracts the frequencies of the AM signal and the local oscillator frequency. It is the extent to which the amplitude of the carrier wave is varied by modulating wave.
a) what should be the operating frequency to have a high frequency gain of 30 % lower that the mid band gain. Assume a DC gain of 100 dB & Dc cut – off frequency @ 15 KHz.?
The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?
Single Sideband Modulator Using Phasing Method
1. The Voltage spectrum of FM signal is shown in Figure 1. The maximum amplitude of modulating signal is 5V. Calculate the bandwidth , modulation index „Carrier frequency, modulating frequency and specify the type of Modulator(narrow band or wide band). 1.54 4.06 4.06 2.45 2.45 0.91 0.91 0.21 0.21 192 194 196 198 200 202 204 206 208 KHZ Figure 1 Reference: (1] Fundamental of Frequency modulation, Pages 150- 163, Principles of Electronics Communication system, Louis E. Frenzel Jr. Check Moodle assignment link for book. DFocus
Draw the circuit of inductor filter and explain its operation.
Find the voltage attenuation ratio for a 30 dB attenuator. Show detailed calculation pls.
Q4: An AM signal: XAM(1)-100cos(100z*10³ t) + 60cos(47*10') *cos(100 * 10³ t). 1) Calculate frequency bandwidth B for XAM(t) signal. 2) Modulation index m%. '
1. Derive the lower cut-off frequency for the basic RC high-pass circuit in Figure 1. R, Figure 1.
it is the fractional value of an AC quantity through which the .6 * .AC quantity has advanced or delayed from the reference point frequency period Peak-to-peak value Phase different phase O
what happens when the modulation order is increased for a modulated signal?
Q4: An analog voltage waveform's information is to be sent with #0.1 percent accuracy through a PCM system. This waveform has a range of -10 V to +10 V as amplitude and 100HZ bandwidth. Compute: 1- The minimum sampling rate. 2- The minimum channel bandwidth required for transmission.