A block of mass m = 3.1 kg is placed on a rough incline surface making an angle 0 = 27.7. with horizontal. Aforce F parallel to the ground is applied to the block. Due to the applied force the block moved x = 0.53 meteralong the inclined surface with constant speed. If the inclined surface has kinetic friction coefficient uk = 0.23what is the work done by the friction force?Provide your answer with 2 decimal places.Take g = 9.81 m/s2HK

Given data: The mass of the block is m=3.1 kg The angle made by the incline is θ=27.7° The movement…

Answered: A block of mass m = 3.1 kg is placed on…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ENGINEERING MECHANICS UPVOTE WILL BE GIVEN. NO LONG EXPLANATION NEEDED. ANSWER ONLY.
Kindly show the complete step-by-step solution. I hope the picture of the asnwer will be clear. Please see the attached photo for the given problem. I will rate you with “like/upvote” after if its clear and understandable.
Help Save & Exit Check Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L= 8 ft and F= 12 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B 30° F T AB : the position vector from A to B. TAB of 17 Next > < Prev 6. 9. 41
If the mass of the hanging-mass is increased and the mass of the cart remains the same, how would the steepness of the position versus t2 be affected? The best-fit line would decrease in steepness.The best-fit line would increase in steepness. Impossible to determine because the net force is not a part of the position vs t2 graph.There would be no change in steepness.
Q2. As shown on the right in image below, the force Facting on the box varies with displacement s, and the coefficient in the image, C = 15. Determine the work done by force Fto the box when the box has displaced s = 0.8 m. Please pay attention: the numbers may change since they are randomized. Negative sign must be included if the work done is negative. Your answer must include 2 places after the decimal point, and proper Sl unit. F (N) F 3 s – C s (m) 1 2.
Need help with this one please thank you:)
Figure The figure shows a schematic of an engine. F, is the force exerted by the combustion gases on the piston (shown by the rectangle at B). FÅ= 50 kN. The angle of the crank OA is 0 = 30° while the angle of the connecting rod AB is p = 15°. Neglect the weight of all members. Also neglect friction between the piston and the cylinder. A 30 cm 10 cm B Fg 0 M₂
The pulley system below is in static equilibrium, where load W3 is 730 N, angle a = 50° and angle 0 = 30O Determine the value of loads W1 and W2, then calculate the ratio of (W1/W2). Give your answer as a ratio of (W1/W2) to two decimal places. a T3 T6 T6 T4 T1 T2 W3 W2 W1
Solve it correctly please.
1) Determine the x and y components of force at pin A. Express your answers in kilonewtons to three significant figures separated by a comma. 2) Determine the x and y components of force at pin D. Express your answers in kilonewtons to three significant figures. Enter your answers separated by a comma.
The shaft below is subjected to the forces shown. Calculate the magnitude of the bearing forces at B. Enter the answer in Newtons. P 20° A C 100 mm 120 mm 100 N 150 mm 200 N 160 mm D 100 mm B Cours
Blocks mị and m2 are connected by a rope as shown in the figure. There is friction between mi and the wall, where the coefficient of static friction is ls. There is no friction between m2 and the ramp. An unknown force P is applied to mį so that mị is about to slip down the wall and m2 is about to move down the ramp. If the magnitude of the normal force on m2 is n2, find m2, the magnitude of P, the magnitude of the friction force on m1, and the magnitude of the tension force in the rope. The knowns are ls, n2, m1, g, and 0. P = ? Hs rope wall no friction m2 = ? ramp

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS