from where that 1 came ????????????? + pgz, = Pgauge2PC;+ pgz 2+1, gauge· If the venturi meter is horizontal then Bernoulli'sEquation reduces to:fromwhere?P+- Р, +2%3D2Eq.1thus- If the continuity equation is applied from section 1 to 2we obtain:C1,idealA,Eq.2C2,idealA

Answered: Image /qna-images/answer/ab47dedb-44c7-42f6-b1b5-839bb619ebb8.jpg

Answered: Pgauge PC; + + pgz, = Pgauge PC + pgz 2…

Pgauge PC; + + pgz, = Pgauge PC + pgz 2 1,gauge 2 + 2 If the venturi meter is horizontal then Bernoulli's Equation reduces to: P+ Р, + 2 pe²2 %3D 2 (R-P.), Eq.1 thus C,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(10) The lead screw of a lathe has a 2.0-in Acme thread, 2%2TPI. To drive the tool carriage, this screw must exert an axial force of 600lb. The thrust is carried on the collar 4½-in outside diameter & 244- in in inside diameter. The lead screw revolves 30rpm. Determine: (a) the efficiency of the screw & the collar, assuming f = 0.15 & fc = 0.10; (b) the power to drive the screw.
Q3 Give the reason for 10 of the following. - 1- The use of lubricant in wire drawing die. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum. 7- The addition of Magnesium and Cerium during the production of Ductile cast iron. 8- The addition of 13% Cr to steel in corrosive environment. 9- The increase of hardness for chips due to the cutting process. 10- The brittle fracture of steel at low temperature lower than -4 C. 11- The heating of metal after the rolling process.
Q2:-Choose the Correct answer. (1):- Grain growth in size (recrystallization) occurs at a- Hot-forming process b- Cold-forming process c- Warm- forming process (2):- The (Vent) is a small opening in the mold to facilitate escape of a- Air and Gases b- Metal e- Sand d-Water (3):- In the Tube Drawing Process, Dies are made of a- Hard Steel b- Copper e- Aluminum d- Wood (4):- The channel through which the molten metal enters the mold cavity called a a- Gate b- Runner e- Riser d- Chaplets (5):- In pressure Die-casting molten metal forced to cavity under a- High pressure b- Low pressure c- Medium pressure d- No pressure (6):- In Electric-Arc Furnaces charge is melted by heat generated from a- Electric are High power b- Electric are Low power e- Laser d- Charcoal (7):- The Hot-chamber die-casting it is limited to use with a- High-melting point metals b- low-melting point metals e- Both
Manufacturing Processes Q1. Chose the correct answer: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b) flanging, (c) hemming, (d) ironing, (e) notching, (f) shear spinning, (g) trimming, and (h) tube bending? 2. Springback in a sheet-metal-bending operation is the result of which one of the following: (a) elastic modulus of the metal, (b) elastic recovery of the metal, (c) overbending, (d) overstraining, or (e) yield strength of the metal? 3. The cutting force in a sheet-metal blanking operation depends on which mechanical property of the metal (one correct answer): (a) compressive strength, (b) modulus of elasticity, (c) shear strength, (d) strain rate, (e) tensile strength, or (f) yield strength? 4. A circular sheet-metal slug produced in a hole punching operation will have the same diameter as (a) the die opening or (b) the punch? 5. As sheet-metal stock hardness increases in a blanking operation, the clearance between punch and die should…
1. Define manufacturing processes, design engineer, industrial engineer and materials engineer? 2. Name and explain a protess to make cylinder shaft? 3. Discus at least three factors which will effect tool life? 4. Define finishing and roughing process? 5. Explain the negative effect of heat generated from machining process? 6. One limitation of sand casting is bad surface finish. Yes or No? Why? 7. What is permeability in casting process? 8. What are the major defects in casting process? 9. Which type of casting process should be use for high melting point casting, such as cast iron and why? 10. Casting problem A certain mold has a sprue whose length is 20 cm and the cross-sectional area at the base of the sprue is 2.5 cm?. The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1560 cm³. Determine: (a) velocity of the molten metal at the base of the sprue, (b) volume rate of flow, and (c) time to fill the mold (in second). mfg m1 Spring 2020 999.pptx
Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C'(4, 0, 5), find (a) the angle between AB and AC, (b) the angle between BA and BC, and (c) the angle between CA and CB. (a) ZBAC = 29.9 (b) ZABC 42 (c) ZACB = 95.225 Submit Question X X > 8
I need the answer as soon as possible
i need the answer quickly
None
where are the steps for the solution?????
Choose all of the processes from below which describe changes which are independent of the path by which the change occurs. the elevation increase experienced by a traveller travelling from Grand Isle, LA to Denver, Coloradothe work required to move a heavy piano up a flight of stairsthe work generated by a homogeneous gaseous chemical reaction carried out inside of a bomb calorimeterthe work accomplished in burning a gallon of gasolinethe heat generated by a car engine as it burns a gallon of gasolinethe heat evolved when a cube of sugar is oxidized to CO2(g) and H2O(g)the latitude increase experienced by a traveller travelling from Baton Rouge, LA to Anchorage, Alaska