Petermine tHhe reaction on the beam 50PN 200N/m I m A f 11.5m 1.55 1.5 m

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: dy = m y2 dx

A:

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: S (-36mm) is correct but total distance traveled (166.04 mm) was marked wrong can you help me?

A:

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Q1 (a) During construction of a highway bridge, the main girders as shown in Figure Q1(a) are…

A: The maximum bending stress in a girder due to this load is 85 MPa.

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: Name the following figures.

A: Pneumatic Cylinder Pivot Bracket with rigid bearing AB7

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: 100 mm- 11.5 mm 7.5 mm N A 225 mm 11.5 mm (a)

A:

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: 200 mm В

A:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: 1. Uf this drawing? 2. What is the name of the company responsible for the drawing? 2. MILWAVKEE…

A: Given :-  9.The drawings are shown in what angle

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: Is this for number 1 only?

A:

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A: As per give condition,  For solution refer below images.

Q: G Determine the equillalent. tiffness for the dreegreem

A: Solution:

Q: Write the Column Formulas?

A: Types Critical load Both ends hinged π2EIl2 one end hinged other end fixed 2π2EIl2 both ends…

Q: This was not correct may you please

A:

Q: 5と 2' 111ド 7K 8'一 16- 251

A:

Q: What is an inflection point?

A: In solid mechanics, an inflection point is defined as a point where the curve of a physical quantity…

Q: The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket is…

A: Esteel=120 GPaμ=.28 εa=100+60×10-6 εb=-200×10-6εc=-180×10-6 θa=0° ,θb=45°,θc=90°

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.