A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below. Given Q2 the following data: S= 1m; 0= 20%; u = 22m/s. (а) How far does the motorcycle move in the x direction before hitting the ground? (b) What is the speed of the motorcycle when it lands?

Q: Name 2 types of bending?

A: Bending is a type of forming process in which the required object maybe a rod, tube or sheet metal…

Q: Warning-If not anything upto the mark, I'll report and dislike you. Draw figure of uniaxial state of…

A: Uniaxial State of stress-  this type of stress has only one principal stress. ie , when an object is…

Q: what would be the order of operations to make this part in the least amount of time and how would…

A: The order of operations to make this part in the least amount of time and how would you hold the…

Q: Define the term distributing force?

A: Distributing force:- Distributing Force is the force acting on the body over a length or surface.…

Q: pes o

A: GIVEN: Explain different types of fits?

Q: Calculate stamping force to produce washers (1/2 inch outside diameter, 3/8 inside diameter) from a…

A:

Q: How did you find out the angle was 90 and how can you find that for other problems?

A:

Q: What is impact loading?

A: Impact loading is a type of loading whose period of action is very less. Generally, when the time of…

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: Propose any improvements if there are any in breaking system

A: The various improvements that can be made in a breaking system are given below. 1. Increasing disc…

Q: A strip of thickness 40 mm is to be rolled to a thickness 20 mm using a two-high mill having a rolls…

A: Given data,  H1= 40 mm  H2 = 20 mm  D= 200 mm

Q: Describe the impact loading?

A: It is a kind of loading where the load is applied for a very small amount of time. In this loading,…

Q: Describe the concept of finding toughness using impact testing machine.

A:

Q: Slots on the outer surface of work piece. (O ocrinding process. (O Planning process. (O Drilling…

A: The term "machining" refers to a number of material removal procedures in which a cutting tool…

Q: A screw jack mechanism is to be incorporated into the machine as part of a levelling system. The…

A: Given                        Pitch, P = 6 mm                      Mass, m = 500 kg Coefficient of…

Q: Explain Schmidt hammer test.

A: Schmidt hammer test principle: When the plunger of the rebound hammer is pressed against the…

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: What does the slenderness ratio serve as?

A: The slenderness ratio is defined as the ratio of effective length to the least radius of gyration.…

Q: Which one of the following material has the sheet metal applications O a. Mild steel O b. Cast iron…

A: Sheet metal is metal forming process which is used for forming into sheets

Q: Why should stress not exceed the material by design?

A: Every component is designed based on working stress which will acts on the component during its…

Q: With a neat sketch explain shaper machine

A:

Q: What is line of impact?

A: The line of impact is the line along which the impact forces act during the collision. Generally, it…

Q: diagram briefly explain the construction and working of a Shaping

A: Surfaces are machined using a shaping machine. It is capable of cutting curves, angles, and a…

Q: Why does the Ultimate tensile Strength (UTS) show a different value than when the test sample…

A: To explain: Why different value from ultimate tensile strength have been got at the time of breaks.…

Q: How were the areas for part 2 found?

A: Given Data and to find: How the areas are calculated?

Q: 1.With a neat diagram ,explain about the working of Single Slope  ADC

A: The is the basic idea behind the so-called single-slope, or integrating ADC. Instead of using a…

Q: Create at least 5 sample of sheet metal joint using recycled tin can.

A:

Q: Give me the process of making a meat tenderizer using a shaper machine process. The picture below is…

A: As we know that it is a tool controlled by hand which makes mellow pieces of meat for cooking.

Q: Automotive body panels are.... Are produced using Additive Manufacturing Usually manufactured by…

A: Given:- Automotive body panels To find:- The manufacturing method for automotive body panels.

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.