Perform the Seismic Analysis of the Centennial Business Center bldg. beside Pulo Brgy. Hall in Pulo, Cabuyao City. (9.1km from the West Valley Fault) ✓ Regular Structure both vertical and horizontal configurations ✓Lateral dimensions = 13.5m x 20m ✓3 storey bldg. with uniform 2.4m storey height ✓ Approximate weight of each storey = 1,050 kN ✓Made of ordinary RC Moment Resisting Frame ✓Location: Pulo, Cabuyao City, Laguna, Philippines Required: Determine the minimum design base shear. ulo-Diezmo Road Nearest Active Fault Trace: 9.1 km Fault Name: Valley Fault System Segment Name: West Valley Fault Year Mapped: 2013 Mapping Scale Used: 1:10,000 Realica Village Pulo Barangay Hall

Perform the Seismic Analysis of the Centennial Business Center bldg. beside Pulo Brgy. Hall in Pulo, Cabuyao City. (9.1km from the West Valley Fault) ✓ Regular Structure both vertical and horizontal configurations ✓Lateral dimensions = 13.5m x 20m ✓3 storey bldg. with uniform 2.4m storey height ✓ Approximate weight of each storey = 1,050 kN ✓Made of ordinary RC Moment Resisting Frame ✓Location: Pulo, Cabuyao City, Laguna, Philippines Required: Determine the minimum design base shear. ulo-Diezmo Road Nearest Active Fault Trace: 9.1 km Fault Name: Valley Fault System Segment Name: West Valley Fault Year Mapped: 2013 Mapping Scale Used: 1:10,000 Realica Village Pulo Barangay Hall

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the simplified design base shear procedure, the near source factor of buildings in zone 4 need not be greater than if no structural irregularities are present 1.2 1.5 1.0 none of the OTHER OPTIONS The coefficient for over-strength and global ductility capacity of a steel special moment resisting frame is 8.5 8. 6. none of the OTHER OPTIONS
Designing and detailing of singly reinforced simply supported beam - BS Code - Manual (BS 8110-1:1997)
What is the story shear force resisted by the columns between the second and third floor? Level Roof 3rd The following shows a schematic section of a three-story reinforced concrete building. The building weights, elevations and seismic story forces are shown in the table below. A F = 1200 k Fard 800 k F-400 k Story Weight (kip) 3,000 k 4,000 k 4,000 k 11,000k Elevation (ft) 42 30 15 Building Elevation and Seismic Story Forces 800 kips 1,200 kips 2,000 kips 2,400 kips Story force, F (kip) 1,200 800 400 2,400K Story shear (kip) 1,200 2,000 2,400 Roof 3rd Flr 2nd Fir Story overturning moment (kip-ft) 14,400 44.400 80,400
HI CAN YOU HELP ME WITH MY ASSIGNMENT. PLEASE WRITE IT PROPERLY, DON'T TYPE IT.
A 250 mm x 500 mm prestressed beam has a simple span of 6m. The beam uses stress relieved tendons with specified strength f,y 1350 MPa and an effective an effective stress in prestressed reinforcement after allowable for prestress losses fe 760 MPa. The prestressed beam is not to be grouted (unbonded) after the application of the prestress. If the area of prestress reinforcement in tension zone is Aps = 1000 mm applied 70 mm above the bottom of the beam and f'c 35 MPa, determine the safe ultimate moment capacity of the beam. (kN-m)
Can you answer please?
B. True-False Questions 7. Leads are not constructed for concrete masonry walls. ( ) 8.A single family detached dwelling cannot legally be built of unprotected wood. ()
An essential 5-story facility structure is conceptualized with an intermediate reinforced concrete moment frame. It is located on a site in zone 4 with a soil profile type Sp. The site is situated 13 kilometers from a potential seismic source type A. The story heights are 5.4 m at the ground floor and 4.3 m for the the 2nd and 5th floors. The story dead loads are 7600 kN from the bottom up. The plan dimensions are 55 m by 37m. The moment frames consist of two four bay frames in the transverse direction and two seven bay frames in the longitudinal direction. Determine the following: 25) Overturning moment at 2nd floor O 99,284 kN-m O 200,069 kN-m O 150,123 kN-m O 109,265 kN-m
For each of the building properties listed below, identify which parameter from the base shear equations shall apply. Building occupancy and function Seismic Base Shear In accordance ASCE-7 code, buildings must be designed to withstand lateral forces that are generated during a severe earthquake. The minimum required design force is given in several equations. Design Base Shear, V= C, W Seismic response coefficient, C,, is the smaller value from two equations: In these equations: C₂ = C₂ < Sp! R Spy R Sor & Spare Seismic Acceleration Parameters from USGS maps is Importance Factor Tis Period of Vibration, (depends on building height & must be calculated) Ris Response Modification Factor from ASCE Table Wis the Effective Seismic Weight of the building. SD1 and SDs, seismic acceleration parameters R, response modification factor I, importance factor T, period None of these
An five-Storey Hotel is to be designed using a two-way slab supported by 400mm x 650mm monolithic beams on the beam-column lines, having a slab dimensions of 5.85m x 7.25m center-to-center spacing. A supper imposed Dead load of 4.55KPa for partition and Live loading of 15.68KPa is specified. Find the required slab thickness, using the steel ratio of approximately 0.0151 maximum, and design the reinforcement for a typical exterior-edge panel (two-sides without continuous slab). Detail the reinforcement, showing size, spacing, and length of rebars. All straight bars will be used. Material strengths will be f’c= 21.5MPa and fy =275MPa. Use combination: 1.2 DL + 1.6 LL. Use the moment coefficient method.