Part A The spool shown in (Figure 1) has a mass of 130 kg and radius of gyration about its mass center of kg = 0.3 m. The force of F = 210 N is applied to the cable. Determine the smallest coefficient of static friction that will prevent slipping on the rail at A. Express your answer to three significant figures. Η ΑΣΦ It vec ? Figure 0.5 m 0.25 m G F 1 of 1 με Submit Request Answer Part B What is the angular acceleration of the spool? Express your answer in radians per second squared to three significant figures. 1 ΑΣΦ 11 vec ? rad/s² Submit Previous Answers Request Answer Incorrect; Try Again; 5 attempts remaining

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: need help with part b i solved a prior

A: ◆ The mean effective pressure: 562.94 kPa. ◆ The indicated power developed by the engine is 4.10 kW.…

Q: Question 11 1 Z Miller index: Write out Miller Index for the plane and direction. Miller Index:

A: Write out Miller Index for the plane and direction.

Q: I need answers to problems 4, 5, and 6 pertaining to the print provided.

A: In the given print the length and diameter of the part is to be calculated. Which is mentioned in…

Q: the parts of a micture can be         using the physical properties of the compund

A: Compounds are substances made up of two or more elements whereas mixtures are made up of elements or…

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: To make 5 cast iron tool holder as shown in Figure 2 on a one time order, and the inside hole…

A: Die casting and forging involves huge initial machine cost , it is not recommended to go for die…

Q: what happened with the 10 in the first equation?

A:

Q: Please sketch this in solidwork and find the surface area and volume. Take a screen shot and post it…

A: The model needs to be drawn on Solidworks and the surface area and volume has to be calculated

Q: Determine the skin due to perforation for a vertical well completion scheme described below: Payzone…

A: To Find:the skin factor due to perforation for a vertical well completion scheme.Given:The pay zone…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: idk where you got the 4 from

A: The number of independent equations=5The number of unknowns=7To determine:Degree of freedom

Q: re did you get 1 for m from???

A: Given data as per questionInitially air containsFirst Phase1P1=30 lbf/in2T1=540°FV1=4 ft3Second…

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: TXY is suppose to be -40.5 where did -40.7 come from?

A:

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: can this be done using simpsons rule?

A: As already calculated using the relation    for the volume ranging from to  in steps of , the…

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: d) Determine the obtuse angle between F1 and F2 using the dot product. Provide Find, Problem…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.