Part A Suppose that L = 6.6 in. (Figure 1) Locate the centroid (, j). Express your answers using three significant figures separated by a comma. vec in. Submit Request Answer Provide Feedback Figure 1 of 1> L H MacBook Air

Q: The block at C is moving downward at vc = 3.2 ft/s. (Figure 1) Figure WAB 2 ft B 3 ft 30⁰ 1 of 1…

A:

Q: Linear Regression u

A: Given: Building Number Number of Employees (X) Vehicle Trips (Y) 1 624 397 2 924 642 3 1260…

Q: Table 1. Reservoirs in the Hydrologic Cycle. 15 Reservoirs Oceans Mass of Water in 10 kg Approximate…

A: Stock and Flow Diagram:

Q: The shape shown in figure below has its centroidal axis y'-y', x, mm from the y axis. Calculate the…

A: Square section dimensions: a1=9 mm, b1=9 mm, Circular section: r2=1.9 mm, xc=0.33 mm.

Q: Suppose that L = 5 in. (Figure 1) Figure 1 in. L 3 in. 3 in. Part A Locate the centroid (, y) of…

A: Given the shaded area and we have to Locate the centroid (x,y) of the shaded area.

Q: GIVEN FIGURE SHOWN, DETERMINE THE FOLLOWING PROMPTS BELOW: у, m В 16, 0) -x, m |F =5 kN 60° *A (12,…

A:

Q: Table 18.8 , verify that the given solution satisfies the governing differential equation and the…

A: Example 1 Given  Deflection of beam , Y=w24Ei-X4+2LX3-L3X At X=0 Y=w24Ei-04+2L03-L3×0Y=w24Ei0Y=0 At…

Q: a. Enter the Moment of Inertia of the triangle (3) about its own centroidal x-axis, I: b. Enter the…

A:

Q: The position of a particle is given by s = 0.33t3 - 0.74t2 - 2.82t + 5.61, where s is in feet and…

A: Consider the given situation S=0.33t3-0.74t2-2.82t+5.61   ftS=distance in feett=time in…

Q: q4

A: Step 1: In the machine it will measure it with the internal measurement tools.  Step 2: First it…

Q: A model known as stopping sight distance is used by civil engineers to design roadways. This simple…

A:

Q: Given the following system of strains, &₂ = 5 + x² + y² + x² + y² &₂ = 6+3x²+3y² + x² + y² Y»…

A: Strain about x-axis, Strain about y-axis, Shear strain,

Q: The following equation is dimensionally homogenous: Acceleration = (velocity)2/(area)1/2 Group of…

A: We have, Acceleration =velocity2area

Q: We are to evalutate the displacement thickness delta* and the momentum thickness theta for a power…

A:

Q: பாத்மகளம்பழியபப்ரீமகவதிபபபபபபபபபய்பா Problem 11.1 - Determine the product moment of inertia of the…

A:

Q: er the bell-shaped volume shown in Figure = 2.6 ft, b = 6.76 ft. z=y2 Suppose 1 of 1 4 Determine the…

A:

Q: (Figure 1) Figure 30 mm 140 mm. 30 mm 30 mm 70 mm 30 mm 170 mm 1 of 1 > ▼ Part A Determine the…

A: to find the centroid of the area about its left edge and the moment of inertia about its vertical…

Q: a. Enter the Moment of Inertia of the rectangle (1) about its own centroidal x-axis, I: b. Enter the…

A:

Q: (Figure 1), a = 45 mm. re 50 mm 150 mm 150 mm 300 mm 1 of 1 Part A Locate the centroid y of the…

A:

Q: I Review the body relative to the cross-section. Consider the pipe assembly shown in (Figure 1).…

A: F1 = 200i-200j-200k F2 = 200i+500j

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.