Part A Consider the truss shown in (Eigure 1). Suppose that F =5 kN. F - 7 kN and F=8 kN Determine the az and y components of reaction at A using scalar notation. Express your answers using three significant figures separated by a comma. VO AE I vec A. A, kN Submit Previous Answers RequestAnswer X Incorrect; Try Again; 2 attempts remaining Part B Figure 1of1 Determine the y component of reaction at Busing scalar notation Express your answer to three significant figures and include the appropriate units. B, - Value Units Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining

Q: How many turns does cog E make?

A:

Q: Please check for the question, verify it is correct or not?

A: There is a half cylinder with length L and radius r.Incoming air velocity is uCoefficient of the…

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Hi, please complete the last three subparts of this question.

A: To calculate the rate of heat transfer, to derive and to calculate the mass flow rate of water, flow…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: 200 m The spool has a mass of 40 kg and a radius of gyration of k-0.65 m. If the 20 kg weight is…

A:

Q: Required information Sally is making a sine bar, which is used to machine angles on parts (see the…

A: Given data: Thickness (t)=1.25 inGroove angle=90°Cylinders diameter d=1 inD=5.6 inθ=22.5° Need to…

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: I need this part answered according to the disrections provided in the image.

A: Match each of the following terms to the phrase that describes it

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: I need help answering this Review Activity

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Please show all the steps, thanks

A:

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

Q: Required handwritten answer, Please be sure . Don't provide wrong answer. 1)An engine produces 238…

A:

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.