Part A A hydraulic jack, which is used to bend pipe as shown in the figure below. Calculate the force F2 on the pipe function of the applied force F1, assuming pressure is constant throughout the system. If F1= 10 kN, L = 50 cm, D1 = 5 cm, and D2 =1 cm

Part A A hydraulic jack, which is used to bend pipe as shown in the figure below. Calculate the force F2 on the pipe function of the applied force F1, assuming pressure is constant throughout the system. If F1= 10 kN, L = 50 cm, D1 = 5 cm, and D2 =1 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A force of 295N is applied to a hydraulic jack piston that is 0.026m in diameter. The second piston that supports the load has a diameter of 0.19m. What is the magnitude of the output force on the hydraulic jack?Ignore any difference in height between the pistons.[Area of a circle = πr2or(π/4)d2]
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ø = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb. what is the maximum weight Wmar of the crate that the system can support? What is the angle e required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) nν ΑΣφ vec Wmax.0 = lb, degrees
13.) Cords are loop around a small spacer separating two cylinders each weighing 400 lb and pass, as shown in the figure over a frictionless pulleys to weights of 200 Ib and 400 lb. Determine the angle 0 and the normal pressure N between the cylinders and the smooth horizontal surface. Total W = 800 Ib 400 lb 200 lb
ANSWER FAST, WILL UPVOTE. NEED HELP
Need handwritten solution in good handwriting and correct answer for an upvote
Needs Complete typed solution with 100 % accuracy.
Draw the free body diagram for this problem: The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom. Neglect the weight of the boom.
10. Find the sum of the forces F1, F2 = 196 N, and F3, if 8 = 60 F3 5 12 F2 8 F₁
The Cylinder weighs 1000 kg, rest on an plane which is inclined at 34° from the horizontal. The normal force acting on a plane to the cylinder is 10 KN. Assume smooth surface, the cylinder leaned to a vertical rod of 8m long and has a weight of 5 KN which was supported by a cable and a hinged (as shown). Find the tensile force of the cable holding the rod and the reactions of hinged to support the cylinder from sliding.
A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r, = 0.0440 m and r, = 0.120 m, respectively. F A (a) If a downward force of F, = 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) N (b) If the smaller piston is pushed down a distance d, = 0.208 m, through what distance d, would the other end move?
Need help please Include all units and steps