Part AA 1.60 m cylindrical rod of diameter 0.450 cm is connected to a power supplythat maintains a constant potential difference of 12.0 V across its ends, while anammeter measures the current through it. You observe that at room temperature(20.0° C) the ammeter reads 18.7 A. while at 92.0°C it reads 17.0 A. You canFind the resistivity for the material of the rod at 20.0° C.ignore any thermal expansion of the rod.Express your answer in ohm-meters.For related problemsolving tips and strategies, you may want to view a VideoTutor Solution of Temperature dependence of resistance.να ΑΣφN. mSubmitPrevious Answers Request AnswerX Incorrect; Try Again; 7 attempts remainingPart BFind the temperature coefficient of resistivity at 20.0°C for the material of the rod.Express your answer in reciprocal degrees Celsius to two significant figures.?a =(°C) 1SubmitPrevious Answers Request AnswerX Incorrect; Try Again; 8 attempts remaining

In the given problem, the cylindrical rod, 1.6 m in length, is held at a constant potential…

Answered: Part A A 1.60 m cylindrical rod of…

Similar questions

Part a and b
A 4600 resistor is connected across a charged 0.850 nF capacitor. The initial current through the resistor, just after the connection is made, is measured to be 0.241 A. Part A What magnitude of charge was initially on each plate of this capacitor? Express your answer in microcoulombs. V— ΑΣΦ q= Submit Part B t = Request Answer How long after the connection is made will it take before the charge is reduced to of its maximum value? Express your answer in microseconds. V— ΑΣΦ Submit Request Answer μC ? us
The high resistivity of dry skin, about 5 x 105 m, combined with the 1.5 mm thickness of the skin on your palm can limit the flow of current deeper into tissues of the body. Suppose a worker accidentally places his palm against an electrified panel. The palm of an adult is approximately a 9 cm x 9 cm square. Part A What is the approximate resistance of the worker's palm? Express your answer with the appropriate units. μA 6 C ? R= Value 4 Units Submit Request Answer
Part A A length of aluminum wire is connected to a precision 10.00-V power supply, and a current of 0.4192 A is precisely measured at 23.5 °C. The wire is placed in a new environment of unknown temperature where the measured current is 0.3698 A . The temperature coefficient of resistivity of aluminum is 0.00429 (°C)-1 What is the unknown temperature? Express your answer using three significant figures. να ΑΣφ ? T = °C Submit Request Answer Provide Feedback
When you connect an unknown resistor across the terminals of a 1.50 VV AAA battery having negligible internal resistance, you measure a current of 17.0 mAmA flowing through it. Part A What is the resistance of this resistor? Part B If you now place the resistor across the terminals of a 12.6 VV car battery having no internal resistance, how much current will flow? Part C You now put the resistor across the terminals of an unknown battery of negligible internal resistance and measure a current of 0.483 AA flowing through it. What is the potential difference across the terminals of the battery?
Part A A 8.8×10-4 V/m electric field creates a 4.9x1017 electrons/s current in a 1.8-mm-diameter aluminum wire. What is the drift speed? Express your answer using two significant figures. "να ΑΣφ ? va = m/s Submit Request Answer Part B What is the mean time between collisions for electrons in this wire? Express your answer using two significant figures. T = Submit Request Answer
Part A Determine the magnitude of the current through resistor R₁, shown in the figure below. The batteries have emfs of ₁ = 6.00 V and E2 = 9.00 V and the resistors have values of R₁ = 14.0, R₂ = 21.6 , and R3 = 30.1 N. R₁ E1 E R3 ww R2 Submit Answe Tries 0/6 Part B Determine the magnitude of the current through resistor R₂. Submit Answer Tries 0/6 Complex network circuit Part C Determine the magnitude of the current through resistor R3.
Question A2 Pure copper has a resistivity of 1.68 x 10-8 Nm. Some accurate cubes of copper are prepared, and electrical measurements are made, for which current is passed across a pair of opposite faces. a) Comparing a 2.5 cm cube and a 5 cm cube, which will have the higher conductance? Ex- plain your answer. b) Given eight 1 cm cubes, how can they be stacked to get the highest and the lowest resis- tance between opposite faces of the stack? Calculate the resistance of each stack.
The figure gives the electric potential V(x) along a copper wire carrying uniform current, from a point of higher potential V, = 8.00 µV at x = 0 to a point of zero potential at x, = 2.60 m. The wire has a radius of 2.10 mm, and copper has a resistivity of 1.69 x 10-8 0-m. What is the current in the wire? V. x (m) Number i Units (A) A
How long does it take electrons to get from a car battery to the starting motor? Assume the current is 320 A and the electrons travel through a copper wire with cross-sectional area 0.120 cm2 and length 0.840 m. The number of charge carriers per unit volume is 8.49 x 1028 m-3. Number i Unit
Part A What is the resistance of A 1.0-m-long gold wire that is 0.50 mm in diameter? Express your answer in ohms. ? R = Ω Submit Request Answer Part B A 10-cm-long piece of carbon with a 1.4 mm x 1.4 mm square cross section? Express your answer in ohms. ? R = Submit Request Answer
Resistance of Carbon A rectangular solid made of carbon has sides lying along the x, y, and z axes, whose lengths are 1.06 cm, 2.12 cm, and 4.24 cm, respectively, as seen in figure below. Determine the resistance for current that flows through the solid in the x direction. Assume the resistivity is p= 3.00E-5 0* m. وا L2 A Tries 0/12 Determine the resistance for current that flows through the solid in the y direction. Evaluate Feedback Print SA Tries 0/12 Determine the resistance for current that flows through the solid in the a direction. Subest Answer Tries 0/12 Post Discussion Send Feedback