Part 1 Power in Decibels and Watts 1. Calculate 10 log() 2. Calculate 101.7 3. Convert 7mW to dBm 4. Convert 1.5W to dBm 5. Convert -2.5dBm to mW 6. Convert 40dBm to watts 7. Calculate 5dBm + 5mW 8. Calculate 3mW - (3dBm)

Q: A1. A circuit containing

A: In the given question there is miss print the circuit will containing 64k words as it is clear…

Q: In optical fiber cables, a glass or plastic core is surrounded by a of less dense glass or plastic.

A: Here in this question we have given optical fiber cable and we have asked to fill some blank space…

Q: (4) Use Simulink to find the Real, Reactive and Power Factor of the source E1. L1 10 mH1 11 10 ARMS…

A:

Q: A certain number of data bits (D) are encoded by a single pulse in one of 2D possible positions…

A: Answer: c PPM

Q: Write an 8051 assembly program to generate 500 Hz square wave from port P1.0 using Timer 0. The…

A: Here is an 8051 assembly program that generates a 500 Hz square wave from port P1.0 using Timer 0:

Q: () Suppose you have an analog signal, explain how will you convert it to digital signal?

A: Analog signals are continuous signals which contains infinite values between two points on signal.…

Q: Is stack linear or no linear data structure? Explain

A: Introduction of the stack: A stack is a linear data structure that follows a Last In First Out…

Q: (e) For a WiFi system, a hot spot has a bandwidth of 30 MHz. i. Calculate the channel maximum…

A: your question is about channel maximum capacity. let's see the solution of the question

Q: Exercise 3: Consider the following sequential circuit with a clock speed of 24 KHz QA QB QC cik clk…

A: the diagram shown above is asynchronous counter using D flipflop. It uses three d flipflop so it…

Q: 1. Describe the applications of the carrier signal recovery and the clock recovery in the…

A: 1) Describe the application of the carrier signal recovery and the clock recovery in the application…

Q: ,Analog to Digital Converter (ADC) needs to be connected to an external clock. If the required…

A: XTAL = Input frequency = 11.0592 MHz Output frequency = 43.2 KHz D flip flops = N = ?

Q: b)how does FWHM apply to an led s characteristics? c) draw the cross sectional view…

A: ANSWER: FWHM apply to an led s characteristics: In the field of LED illuminated presentation, the…

Q: Sketch the output of the clamper network with sine waveform.

A:

Q: The core diameter of a single-mode fibers is about a. 10 times the fiber radius b. 7 times the light…

A: I have given solution in step2

Q: A common base amplifier is referred as a O a. voltage amplifier • b. emitter follower C. current…

A:

Q: A common base amplifier is referred as a a. none of these O b. power amplifier O c. emitter follower…

A: a common-base (also known as grounded-base) amplifier is one of three basic single-stage bipolar…

Q: Q. Use Table below to explain why the circuit of Figure below will not work as it is. How can the…

A: Given schematic diagram is shown below. A, B, and C are the inputs in the figure above. The outputs…

Q: 5- Find the pulse width for a monostable timer if R= 100KQ and C= 100μF?

A: As per our guideline we have supposed to answer one question at time, so i have solved Q-5 for you,…

Q: Short questions: Q. 11 kbps is equals to how many Bps?

A: According to bit conversion, 1 kbps= 125 Bps

Q: 2. If the period of a PWM signal is 1500 counts and the desired duty cycle is 20%, what is the pulse…

A: 1) The duty cycle describes the amount of time the signal is in a high (on) state as a percentage of…

Q: In optical fiber, the core has a higher refractive index than the cladding. Select one: O True O…

A: In optical fiber the core has a higher refractive index than the cladding true or false.

Q: Q1) Give a short answer (Choose five branches): a) Draw block diagram for transmitter digital…

A: Answers: a) A block diagram for a transmitter in a digital wireless communication system typically…

Q: a: Design of Microstrip antenna which operating at frequency of 890 MH2 using the program hfss

A: It is defined as a low-profile antennas. A metal patch mounted at a ground level with a di-electric…

Q: Q1: For the following State diagram, drive the equivalent ASM chart 00/ Z2 OX / Z4 10/Z3 01/0 Sa/Z…

A: Given: A state diagram is given with three states Si and five outputs Zi.  Asked: We need to make…

Q: For an 8-PSK system operating at an information rate of 36 kbps determine, (i) Baud

A: The Answer is

Q: O Reference pulse gen O LPF and multiplier ci O LPF and holding circ

A: given - PAM Demodulator consists ofComparator and SawtoothFlip flop and LPF Reference pulse…

Q: Example 2 (ADC) done in class uses an Atmega16 and an 8-bit ADC (ADC0808) to convert a analog signal…

A: Since it is an apparatus related question, we can only help with the steps.

Q: Use PHP A P  type semiconductor has acceptor level 57 me above the valence band. What is maximum…

A:

Q: The frequency of ac signal that complete three period in 10 ms is Select one: O 1. 10kHz OI. 30 Hz O…

A: The Frequency of ac signal that complete three period in 10 ms is : 300HZ

Q: What is the maximum PWM period possible for the KL25Z TPM with a prescale of 128 an input clock of…

A: 2.4 sec , this means 1 cycle takes approx 2-2.5 sec- a cycle is one complete high then low pulse.

Q: Determine the sizing of the two gates (x, and y) that will minimize the propagation delay? Let…

A: According to the information given:- We have to find the correct option to satisfy the mention…

Q: While comparing transformer utilization factor (TUF), the bridge rectifier has a TUF Select the…

A: The ratio of the DC power available at the load resistor to the AC rating of the secondary coil of a…

Q: Q. 528 kbps is equals to how many Bps?

A: In network bandwidth, 1 kbps = 125 Bps

Q: Design a transistor level circuit for the function F using CMOS. The circuit you design múst have…

A:

Q: Q. 5 kbps is equals to how many Bps?

A: This question is belongs to network bandwidth.

Q: Digital Computer Logic CSE200 Instructions: Date: 07-04-21 Attempt all questions. Q.1.(a) Briefly…

A: difference is an given below : BASIS FOR COMPARISON ANALOG SIGNAL DIGITAL SIGNAL Basic…

Embedded Software Development

Using specific programming languages (like C and C++) to write code for a specific hardware device in which it runs is called embedded software development. It makes the device smart by performing actions based on user's input which improves the user experience. They are designed to perform function-specific tasks rather than doing multiple tasks like computers. The embedded system is incredibly intuitive. An embedded software system could be a system developed and organized on any device, apart from an old-fashioned computer. It is the brain of a specific device; however, it is a solely useless tool and simple to elucidate what software system is embedded.