Part 1A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d - 260 mm,di - 261.0 mm, and d2 - 259.3 mm. For the deformed plate, determine(a) the normal strain of diagonal QS.(b) the shear strain ,y at corner P.UndeformedDeformeddzddiCalculate the deformation of diagonal QS.Answer: Sosimm Part 2Calculate the normal strain of diagonal QS.Answer: eos = ieTextbook and MediaSave for LaterAttempts: unlimited Submit AnswerUsing multiple attempts will impact your score.20% score reduction after attempt 4Part 3Calculate e, the angle that side PS makes with side PQ after deformation.Answer: 0 = iradeTextbook and MediaAttempts: unlimited Submit AnswerSave for LaterUsing multiple attempts will impact your score.20% score reduction after attempt 4Part 4Calculate the shear strain at corner P.Answer: Yp =pradeTextbook and MediaSave for LaterAttempts: unlimitedSubmit Answerultin

Answered: Image /qna-images/answer/c1a54c6d-b860-4ad0-b4fd-b91d55acfe7e.jpg

Part 1 A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d - 260 mm, di - 261.0 mm, and d2 - 259.3 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain yy at corner P.

Part 1 A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d - 260 mm, di - 261.0 mm, and d2 - 259.3 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain yy at corner P.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the value of strain stress 30 MPa Modulus of elasticity=65 MPa
In a volume element with dimensions dx, dy, dz the negatíve y-face has a 2 MPa stress in the positivex-direction, a 3 MPa stress in the negative z-direction, and a 4 MPa stress in the negative y-direction. Which of the following describes the stresses per elasticity convention? Oy = 4 MPa Oyr = -2 MPa Oyz = 3 MPa Oy = -4 MPa Oye = 2 MPa Oyz = -3 MPa Oy = 3 MPa Oye = -4 MPa Oyz = 2 MPa =4 MPa Oyr = 2 MPa Oyz = -3 MPa
h.w: A compressive force was applied in the longitudinal direction of a cross-sectional bar ( A= 10 cm) and this resulted in a longitudinal strain of (0.0007) Calculate the amount of force? If you know that the elastic modulus (E= 206*10° m2
A rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains. PLEASE ANSWER I,G,H
Angle a=36 Angle b=53 The tolerance is ±1%
The bar ABC in the figure consists of two cylindrical segments. The material of the bar has the stress-strain diagram shown. Calculate the strain in segment AB caused by the 60-kN axial load. 50 50mm 40 40mm 30 60 kN 60 kN 20 10 B 500mm 400mm 0.0000 0.0005 0.010 0.015 0.020 0.025 0.030 D.035 D.040 STRAIN SSHELS
I need help with iv and v
4 In a plane stress condition, the components of stress at a point are ox= 20 MPa, oy = 80 MPa and Oxy = 40 MPa the maximum shear stress (in MPa) at the point is
Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below. The diameter of the bar is d 180 mm. A bending moment is applied that causes the neutral axis to become concave up. What is the normal strain h = 30 mm from the bottom of the bar if the radius of curvature is measured to be p Express your answer to three significant figures. ▶ View Available Hint(s) £= - ΠΙΑΣΦ vec ? Ax mm/mm 5.4 m?
View Policies Current Attempt in Progress At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 180 MPa, o, = 50 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. y Ox At this point, determine the strain components &x, Ey, E, and Yxy. Assume that E = 73 GPa and v= 0.31 for the machine component. Ex = με Ey = με με urad Attempts: 0 of 3 used Submit Answer E₂ = Yxy= Save for Later
In mechanical resistance
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition determine: -all 3 principle stresses, the max in plane stress, average noemal stress and the absolut max shear stress. - Show the principle stress, the max inplane shear stress and the average normal stress on an appropriate schematic