Pampanga sand with G, = 2.51 is mixed 26% by weight of water and compacted to produce a cylindrical%3Dsample of 48 mm diameter and 96 mm long with 7% air porosity. Calculate the void ratio of the sample.

Answered: Image /qna-images/answer/80755138-a254-42c3-8491-d270cf54b172.jpg

Pampanga sand with G; = 2.51 is mixed 26% by weight of water and compacted to produce a cylindrical sample of 48 mm diameter and 96 mm long with 7% air porosity. Calculate the void ratio of the sample.

Pampanga sand with G; = 2.51 is mixed 26% by weight of water and compacted to produce a cylindrical sample of 48 mm diameter and 96 mm long with 7% air porosity. Calculate the void ratio of the sample.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.12P

See similar textbooks

Related questions

Q: The difference between maximum void ratio and minimum void ratio of a sand sample is 0.25. If…

A: DIfference betweeh max. void ratio and min, void ratio = 0.25 Relative density of this sample = 60…

Q: 2.10 A dry quartz sand has a density of 1.68 Mg/m³. Determine its density when the degree of…

Q: The soil sample in natural state having a volume of 0.0012 m3 weighs 1.73 kg. The degree of…

A: Given data : Volume of soil (V)=0.0012 m3Initial weight (Wi)=1.73 kgWeight after drying (Wf)=1.44…

Q: A sample of soft saturated clay has a volume of 100 cu.m. and weighs 175 gr. If the oven dry unit…

A: 1.) The expression for water content of soil is given as water content of sample=weight of saturated…

Q: The total density of sand in an embankment was found to be 1900kg/m^3 and the field water content…

Q: The natural water content and in-situ unit weight of a sample of sand above water table are 14% and…

A: Given data : Void ratio in densest state emin=0.48 Void ratio in loosest state emax=0.80 Water…

Q: The results of a laboratory consolidation test on a clay specimen are the following. Pressure, r…

A: In this question we have asked elong curve and preconsolidation pressure and compression index…

Q: A soil specimen has a total volume of 70 cm3 and a total mass of 135.5g. After complete drying in an…

A: V = 70 cm^3 Wet weight W1 = 135.5 g Dry weight W2 = 122 g Gs = 2.60 Void ratio e = ?

Q: A certain saturated sand (S = 100%) has a moisture content of 25.1% and a specific gravity of solids…

Concept explainers

Calculation of Settlement

The vertical displacement of the structural foundation due to the loading from the superstructure is known as settlement. It is due to the reduction of air voids present in the soil. The amount of vertical displacement depends on the bearing capacity of the soil on which the foundation is laid. The effect of the settlement depends on the magnitude of settlement, uniformity, and the structural design of the structure. The maximum allowable settlement for residential and office buildings should be less than 18 mm, for industrial buildings, it is 38 mm and for commercial buildings, it is 25 mm.

Question

Pampanga sand with G, = 2.51 is mixed 26% by weight of water and compacted to produce a cylindrical
%3D
sample of 48 mm diameter and 96 mm long with 7% air porosity. Calculate the void ratio of the sample.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

i need the answer quickly
A sample of moist sand taken from the field was found to have a moisture content of 14% and a porosity of 38%. In the laboratory test that simulates field conditions, it was found that at its densest state, its void ratio is 85% and at its loosest state its void ratio is 40%. Determine the void ratio. Select one: a. 0.79 b. 0.57 c. 0.61 d. 0.42
The coefficient of permeability of sand at a void ratio of 0.80 is 0.47 mm/s. Estimate the coefficient of permeability of this sand at a void ratio of 0.50.
A sample of uniform sand has a porosity of 43%.From the lab test, the value of the void ratio in theloosest condition is 0.85 and a void ratio of 0.35 inthe densest condition. If the water content is 12%and Gs = 2.7. Determine the following:a) Density indexb) Degree of saturationc) Determine the moist unit weight
The natural water content and in-situ unit weight of a sample of sand above water table are 14% and 119 pcf respectively. The emax and emin corresponding to the loosest and densest states as determined by laboratory tests on dried samples are respectively 0.80 and 0.48. If the particle specific gravity is 2.65, calculate S and Dr.
hand written solution in white page neat clean all units and formula concept mentioned
A clean sandstone core sample with diameter of 3.8 cm and length of 5.6 cm is saturated with a brine. The core was desaturated in several steps, and the resistance was measured at each saturation. The results are as follows: Water Saturation (Fraction) Resistance (k2) 1.000 1.302 0.900 1.695 0.800 2.283 0.730 2.878 0.640 3.775 0.560 5.637 0.480 7.838 0.375 13.175 0.350 17.050 0.300 26 Brine resistivity= 0.74 Qm Archie coefficient =1.03 Cementation factor= 2.2147 (1) Estimate the rock porosity. (2) Determine the saturation exponent. (3) Estimate the amount of oil and brine (in cc) in the core sample when resistivity index is 5. All steps of the calculations should be shown.
3- Following are the results of a laboratory consolidation test on a sample of undisturbed clay obtained from the field. Final height of specimen (in) Pressure, o' (lb/ft') 1 0.9917 1,000 2,000 4,000 0.9843 0.956 0.9142 8,000 0.8685 16,000 0.8228 32.000 The height of the specimen at the beginning of the test was 1.0 inch, and the diameter was 2.5 inches. The moist specimen weighed 0.31 lb and the water content was determined to be 19%. Estimate the compression index and the preconsolidation pressure from the e-log o' curve. (Plot in Excel) Given: Gs = 2.7.
The total density of sand in an embankment was found to be 1900kg/m^3 and the field water content was 12% . In the laboratory, the density of the solid was found to be 2660 kg.m^3, and the maximum and minimum voids ratio were 0.63 and 0.44, respectively What is the void ratio of the sand? Calculate the relative density of the sand in the field:
An undisturbed sample of fine sand is tested in the laboratory and found to have a dry mass of 3.23 kg, a total volume of 0.00187 m3and a specific gravity of 2.65. Other laboratory tests are performed to determine the maximum and minimum density for the sand. At the maximum density, it is determined that the void ratio is 0.38; at the minimum density, the void ratio is 0.85. Determine the relative density of the undisturbed sample.
A sand sample has a porosity of 30% and specific gravity of solids as 2.6. What is its degree of saturation at moisture content of 4.94%?
4.15 The following results were obtained from a liquid limit test on a clay using the Casagrande cup device. Number of blows 6 12 20 28 32 Water content (%) 52.5 47.1 43.2 38.6 37.0 (а) Determine the liquid limit of this clay. (b) If the natural water content is 38% and the plastic limit is 23%, calculate the liquidity index. (c) Do you expect a brittle type of failure for this soil? Justify your answer.