P4-7) Create an orthographic projection of the following object. Draw the three standard views. SLOT GOES STRAIGHT THROUGH 2.00 1.00 2.75 1.00 é 1.50 1.00 2.75

Q: Problem 2 CE Board Nov 2018 If a spiral 80 m long connects with a 6.5 degrees circular curve,…

A:

Q: The system shown starts from rest. What should the mass M2 be so that the 8 kg mass drops 0.98m in…

A:

Q: A simply supported beam of 8.5 m span is to carry a uniform ultimate load of 60 kN/m. The beam…

A: GIVEN Length of beam=8.5m Uniformally distributed load (Wu)=60KN/m Beam dimension =250mm*450mm…

Q: 2. Calculate the value of y at the free-end, slope at the supports. Use E = 200 GPa, I = 150 x…

A:

Q: Given the compound curve with the vertex V inaccessible, angles A and B are equal to 16°20' and…

A:

Q: For the given structures, determine the degree of indeterminacy. 7. A 7

A:

Q: 100 KN 60 kN 3m J G 4m 3m 40KN D 3m A Second Level: 100 KN 1.5m H B First Level: 100 KN 3m 60KN 1.5m…

A:

Q: An automobile moving at a constant velocity of 45 feet per second passes a gasoline station. Two…

A:

Q: The coefficient of friction between the 50 Ib weight and the 300 Ib weight is 0.5. The 300 lb weight…

A: When anybody on the mechanics moves on the surface, the surface gives the resistance force termed…

Q: can you write step 4? its okay to not include the drawings

A: Step-4 Dead load on gridline-1

Q: Compute the deflection at C. A 5 m I 200 KN B 100 KN 10 m 21 E = constant = 250 GPa I=600(106) mm4 C…

A: Given, Simply supported beam with two point loads  E = 250 GPa or 250000 MPa I = 600 x 106 mm4

Q: The location of plastic NA from the top of the section as shown in figure is (round off to one…

A: For given section, as shown below,To find  the the location of plastic NA from the top of the…

Q: Calculate the value and location of the maximum deflection.

A:

Q: The angle between a 5-m full station of a certain curve is 10°. The curve has 7 intermediate…

A: Some points to be considered 1) Point of curvature 2) Point of tangency 3) Length of the Curve   The…

Q: determine the constant deceleration

A: This question has been taken from transportation engineering

Q: upvote for handwritten. Please skip if you have already done this. Thank you

A:

Q: What does the drawing module provide?

A: drawing modules:

Q: The two masses m;:=3.75kg and m;=4.25kg are joined by strings. If the masses are accelerated to the…

A:

Q: average weight of the pony (in kilogr 6 12 16 22 0 95 140 172 181 ke a scatter diagram of the data.

A: Given: Take x be the age of pony whereas y be the average weight

Q: The beam ABCD with a cross section carries the loading shown in the figure. Determine the magnitude…

A: Find:Magnitude and location of maximum bending stress in the beam

Q: SAMPLE PROBLEM: Given in the accompanying tabulation are the observed data for a traverse obtained…

A:

Q: Three guy wires with forces indicated in the figure are attached to an anchor bolt. Determine the…

A: Given figure shows three guy wires attached to an anchor bolt. It is required to calculate the…

Q: e. Calculate the value of the deflection at the free-end in terms of El, w or P, and L. a. b. P w…

A:

Q: Using the following notes, what is the elevation of BM14 Station BS FS Elevation BM12 4.64 209.65…

A:

Q: A 5kg block has a rope of mass 2kg attached to its underside and a 3kg block is suspended from the…

A: Given:- A 5 kg block has a rope of mass 2 kg attached to its underside and a 3 kg block is suspended…

Q: For the given structures, determine the degree of indeterminacy. 3. 3

A: The given structure has two fixed supports at ends and one roller support in the middle. The fixed…

Q: For the str4ctures lcaded as shown, determine the reactions at the sPPorts usin9 poth the graphical…

A:

Q: Design most efficient rectangular channel to safely carry a discharge of 15m³ /sec. The channel is…

A: Discharge (Q) = 15m3/sec Channel constructed using concrete, therefore Manning coefficient n = 0.013…

Q: Determine the displacement figure. Take E = 200GPa, I = 300E6 mm4 120 kN.m A 3m 30KN B at D of the…

A: Data given E = 200×103 MPa I = 300×106 mm4 Find: displacement at D

Q: P4-17) Create an orthographic projection of the following object. Draw the three standard views. 250…

A: To draw the orthographic projections.

Q: Given in the tabulation below are notes for an open traverse. Determine the latitude and departure…

A:

Q: Q2: Use commands (line, arc, rectangle, mtext), then List all required commands to draw the…

A: Required command to draw above dish Rectangle command to draw inner and outer rectangles Arc…

Q: Determine the acceleration of the system shown. 30 30 12 kg 8 kg

A:

Q: Figure below is a shaft which is held by different type of bearings. Calculate the resultant…

A:

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.