Use the force method (method of consistent distortions) to find the value of the redundant force indicated for each truss. E is constant for all members. Find redundant Rcy. All bar areas are the same.BOD60 kProblem 12.1P12.4P12.2Find redundant Re. All bar areas are the same.160 k50 k.A.BK20 ft-D..-20 ft-Problem 12.220 ft

Answered: P12.2 Find redundant Re. All bar areas…

Engineering

Civil Engineering

P12.2 Find redundant Re. All bar areas are the same. 160 k 50k D.. 20 ft 20 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

14.10 Given: The truss shown is made up of links DE, CE, CD and BC. All four links have the same cross-sectional area A. A vertical load P is applied to joint D. The failure stress in tension for each link is (OT) fail, and the allowable stress in compression for each link is (oc) fail Find: Using a factor of safety FS, determine the maximum allowable load P on the truss. L = 1.5 ft. D 60° 60° -L E Use the following parameters in your analysis: A = (oc) fail 12ksi. B 0.5in², (OT) fail 20ksi and
The system shown below is comprised of the cantilever beam AB and the supporting truss BC connected to each other by a pin joint at B. Using the Stiffness Method compute the displacements and internal forces in the system under the applied load. Use a frame element to model member AB to account for axial stiffness. Take E = 250 GPa, IAB = 2x10 mm4, AAB = 2x104 mm², Aec = 1x10³ mm². A 80 KN 2 m * 4 m 6 m OB
A snow load transfers the forces shown to the upper joints of the Pratt and Howe roof lattices shown below. Ignoring the horizontal responses on the supports ( \(A x=Ex=0 \)) a) Determine the forces in all members using the joint method. Pratt Roof Truss System: AA A 2 Rods Pull Push CC=5,7 WIDTH (m) x=2 y=3,4 height (m) z=4,2 X 1 BB H 2 y 3 CC G y BB 5 D F X Pratt Roof Truss System SOLUTION: 6 AA E A 4-digit number must be written after the comma. For example 14.7845. Forces (kN) AA=4,2 BB=4,2 A
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young’s modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work.
Disregard the DL on CD. Solve using regular stiffness and again using modified stress for all members that qualify
6. A 2-bar truss is as follows. AB= 4 m, BC=5 m, AC=3 m. The black block on C is a friction plate. When the friction coefficient is greater than u, the truss is stable. Determine the value of μ. A P B Hint: First, determine the internal force of AB and BC bar by Joint method at Joint B, Second determine Cx, Cy by Joint method at Joint C; then determine the value of µ.
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. 6.8 m 41° Answers: AB= AD= BC= BD = CD= i i i 6.4 m 6.4 m 6.8 m, B 6080 N Z Z N N N N N
three forces are exerted in the joint of a truss as shown. The system is in equilibrium. draw the force polygon for the equilibrium in the joint. determine the forces n1 and n2. are they tensile or compressive forces
Determine the force in member BC of the loaded truss. The force is positive if in tension, negative if in compression. 2.5 kips 3.9 kips 4.6 kips Answer: BC = i kips
Current Attempt in Progress Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. A 66 49° 12° W Answers: AB = i W AC = i W BC = i W
Find the force in each member of the truss by using: The method of consistent deformations. Take the member AB as a redundant. The stiffness EA is constant. 1.2 m 0.9 m B 10 kN 0.9 m ALIA