Given: • The density of water is 62.4 lbm/ft3 • The specific gravity of the fluid is 0.7 • The viscosity of the fluid is 20 CP The piping system is shown above and contains the following fittings: • 20 90 degree bends ; K = 10f 。 13 gate valves ; K = 7f • 4 check valves ; K = 21f ° 6 tee runs ; K = 16f 2 tee branches ; K = 60f ⚫ The piping system dimensions are as follows: A=15ft; B=215ft; C=60ft What is the volumetric flow, ft3/s, through the pipe? What is the velocity, ft/s? What is the pressure drop, psi, due to the pipe? What is the pressure drop, psi, due to the pipe and fittings? What is the pressure at P1, psig? If the piping system was full of liquid but the flowrate was 0 gpm. What would P1 P2 be, psig? P1 E B P2 A A liquid flows through a piping system from P1 to the top of a structure at P2 The entire piping system is 4 sch 40 pipe The piping system is intended to provide liquid at a rate of 80 gpm while maintaining a P2 pressure of 32 psig. The flowrate at P1 and P2 are the same. (ie.. there is no splitting or branching of the flow) The friction factor, f (fanning), can be assumed to be 0.005

Introduction to Chemical Engineering Thermodynamics
8th Edition
ISBN:9781259696527
Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Publisher:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Chapter1: Introduction
Section: Chapter Questions
Problem 1.1P
icon
Related questions
Question
Given:
• The density of water is 62.4 lbm/ft3
• The specific gravity of the fluid is 0.7
• The viscosity of the fluid is 20 CP
The piping system is shown above and contains the following fittings:
• 20 90 degree bends ; K = 10f
。 13 gate valves ; K = 7f
• 4 check valves ; K = 21f
° 6 tee runs ; K = 16f
2 tee branches ; K = 60f
⚫ The piping system dimensions are as follows: A=15ft; B=215ft; C=60ft
What is the volumetric flow, ft3/s, through the pipe?
What is the velocity, ft/s?
What is the pressure drop, psi, due to the pipe?
What is the pressure drop, psi, due to the pipe and fittings?
What is the pressure at P1, psig?
If the piping system was full of liquid but the flowrate was 0 gpm.
What would P1 P2 be, psig?
Transcribed Image Text:Given: • The density of water is 62.4 lbm/ft3 • The specific gravity of the fluid is 0.7 • The viscosity of the fluid is 20 CP The piping system is shown above and contains the following fittings: • 20 90 degree bends ; K = 10f 。 13 gate valves ; K = 7f • 4 check valves ; K = 21f ° 6 tee runs ; K = 16f 2 tee branches ; K = 60f ⚫ The piping system dimensions are as follows: A=15ft; B=215ft; C=60ft What is the volumetric flow, ft3/s, through the pipe? What is the velocity, ft/s? What is the pressure drop, psi, due to the pipe? What is the pressure drop, psi, due to the pipe and fittings? What is the pressure at P1, psig? If the piping system was full of liquid but the flowrate was 0 gpm. What would P1 P2 be, psig?
P1
E
B
P2
A
A liquid flows through a piping system from P1 to the top of a structure at P2
The entire piping system is 4 sch 40 pipe
The piping system is intended to provide liquid at a rate of 80 gpm
while maintaining a P2 pressure of 32 psig.
The flowrate at P1 and P2 are the same. (ie.. there is no splitting or branching of the flow)
The friction factor, f (fanning), can be assumed to be 0.005
Transcribed Image Text:P1 E B P2 A A liquid flows through a piping system from P1 to the top of a structure at P2 The entire piping system is 4 sch 40 pipe The piping system is intended to provide liquid at a rate of 80 gpm while maintaining a P2 pressure of 32 psig. The flowrate at P1 and P2 are the same. (ie.. there is no splitting or branching of the flow) The friction factor, f (fanning), can be assumed to be 0.005
Expert Solution
steps

Step by step

Solved in 2 steps with 4 images

Blurred answer
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Introduction to Chemical Engineering Thermodynami…
Introduction to Chemical Engineering Thermodynami…
Chemical Engineering
ISBN:
9781259696527
Author:
J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart
Publisher:
McGraw-Hill Education
Elementary Principles of Chemical Processes, Bind…
Elementary Principles of Chemical Processes, Bind…
Chemical Engineering
ISBN:
9781118431221
Author:
Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:
WILEY
Elements of Chemical Reaction Engineering (5th Ed…
Elements of Chemical Reaction Engineering (5th Ed…
Chemical Engineering
ISBN:
9780133887518
Author:
H. Scott Fogler
Publisher:
Prentice Hall
Process Dynamics and Control, 4e
Process Dynamics and Control, 4e
Chemical Engineering
ISBN:
9781119285915
Author:
Seborg
Publisher:
WILEY
Industrial Plastics: Theory and Applications
Industrial Plastics: Theory and Applications
Chemical Engineering
ISBN:
9781285061238
Author:
Lokensgard, Erik
Publisher:
Delmar Cengage Learning
Unit Operations of Chemical Engineering
Unit Operations of Chemical Engineering
Chemical Engineering
ISBN:
9780072848236
Author:
Warren McCabe, Julian C. Smith, Peter Harriott
Publisher:
McGraw-Hill Companies, The