P.19.4. If the shear load of 100 kN acting in the vertical plane of symmetry of the wing box shown in Fig. P.19.2 now acts in the plane of the web 72, calculate the rate of twist in the section and the maximum .shear stress 100 KN 500 mm 2 F100 mm 100 mm 200 mm 200 mm 8 600 mm .Answer: 5.6 10-6 rad/mm, 140.7 N/mm2

P.19.4. If the shear load of 100 kN acting in the vertical plane of symmetry of the wing box shown in Fig. P.19.2 now acts in the plane of the web 72, calculate the rate of twist in the section and the maximum .shear stress 100 KN 500 mm 2 F100 mm 100 mm 200 mm 200 mm 8 600 mm .Answer: 5.6 10-6 rad/mm, 140.7 N/mm2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Parvinbhai
A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 602 MPa, and the Poisson's ratio as 0.20. Express your answer in three decimal places.
Q.5) A bar of 1000 mm length and 40 mm diameter is centrally bored for 300 mm length at one end at a diameter of 20 mm. Young's modulus of the material is 2 x 10° N/mm². If the bar is 2 40 mm 20 mm 700 mm 300 mm loaded axially with a load of 30 kN the extension produced is (A) 0.1136 mm (C) 0.1478 mm (B) 0.1313 mm (D) 0.1542 mm
Do problem 1.26 question a
A hellcal spring Ils made by wrapplng steel wire 20 mm diameter around a forming cyllnder 160 mm in diameter. Calculate the elongatilon of the spring wlthout exceeding a shearing stress of 150 MPa If It ls composed of 20 turns. Let G=80,000 MPa. (Ans. 127.4 mm)
200 mm 1.36 The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a 20-mm-diameter pin at D that is in double shear. Determine (a) the required diameter of the connecting rod AB, given that its tensile working stress is 100 MPa; and (b) the shear stress in the pin. -240 mm- 50 mm 10° 60° FIG. P1.36 30 kN 150 mm- FIG. P1.37 50 mm
The extruded plastic shape has dimensions of D = 24 mm, d = 18 mm, a = 87 mm, and t = 3 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 335 N. (b) If the allowable shear stress for the plastic material is 2400 kPa, what is the magnitude of the maximum shear force Vthat can be applied to the extrusion? a Answer: (a) TA = КРа (b) V = N
A threaded machine bolt of 3/4 in diameter is screwed up tightly, fastening together two steel parts. To avoid the failure of the bolt in shear, the unit shearing stress must not exceed the elastic limit stress of 36000 psi. What maximum pull may safely be exerted on a wrench with a 20 in. moment arm to avoid failure on the root area if its root diameter is 0.6688 in. and if we assume that friction under the bolt head nullifies 25 percent of the pull
ABO(sub1) and BCO(sub2) is a quarter circle with the given dimensions. Let R(sub1) equals to 10 inches. If the section is constant and has a length of 5 ft., The shear load P is acting on the centroidal position from the spar web. Determine the shearing stresses developed in the nose skin and spar web, shear center and the angle of twist. Let G = 4 x 10^6 psi. The thicknesses as follows, for nose skin = 0.080in, for sparweb = 0.10in. -What is the angle of twist? -What is the shear center? hef = 3R1 = 30in P = 6000lbs A %3D F 2R1 02 В 01 R1 D E 4R = = 40in
PART 1 My answer Ay=14.38 Cy=13.62 Part 2 Determine the shear force acting at each of the following locations: (a) x = 4.25- (i.e., just to the left of point B.) (b) x = 4.25+ (i.e., just to the right of point B.) (c) x = 9.25-(i.e., just to the left of point C) (d) x = 9.25+ (i.e., just to the right of point C) My Answer: (a) V= 14.38 kN (b) V= 14.38 kN (c) V= 14.38 kN (d) V= 28 kN Part 3 Determine the bending-moment acting at each of the following locations: (a) x = 4.25-(i.e.. just to the left of point B.) (b) x = 4.25+ (i.e.. just to the right of point B.) (c) x = 9.25 m (i.e., at support C) (d) x = 8.25 m My Answer: (a) M= 61.115kN-m (b) M= -148.885 kN-m (c) M= -76.985 kN-m (d) M= -91.365 kN-m Part 4: Use your bending-moment diagram to determine the maximum positive bending moment, Mmax, pos, and the maximum negative bending moment, Mmax, neg. Use the bending-moment sign convention detailed in Section 7.2. The maximum negative bending moment is the negative moment with…
Q3/ Fig. 3 shows a cost iron bracket of cross-section of I-form. Determine the maximum bending moment that should be imposed on this section if the tensile stress in the top flange is not to exceed 40 MN/m² What is then the value of the compressive stress in the bottom flange? Fig. 3 40 mm 200 mm mm 200 mm T 40 mm 120 mm