OUT+ 十 102 R5 LONG 777 B- LARI B+ TP4056 465F2P Ci C2 8205A CGANZ 18 03962A O R3 122 C3 OUT-

Q: One can conceive an atomic nucleus, as a sphere charged uniformly, and positively. Let the proton…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Using the supernode concept to determine the voltage marked v20 in the figure, the crossed wires…

A:

Q: Calculate if th=2 V and t = 1 V. Express your answer to three significant figures and include the…

A: For the given operational amplifier circuit the value of the output voltage for various values of…

Q: A 90 MVA synchronous generator has an inertia constant of 3s. Then,. O a) None of these b) It has…

A:

Q: What Is the opposite of redistance

A: Resistance R The property which is oppose flow of charge carriers( electrons  ) .the element is…

Q: 230V Primary, 12v Secondary T1= 250mA stepdown transformer 12 D5 230V AC IN T1 1A Bridge IC2 7812…

A: Single-phase Bridge circuit: It produces the DC output and takes AC input. This is a type of…

Q: E R www 1=5 A

A: The given circuit is a simple electric circuit with voltage source, Resistance and a Bulb. We need…

Q: 5 factors in making a schematic diagram using fritzing

A:

Q: D8.22 Consider the folded-cascode amplifier of Fig. 8.36 for the following case: Vpp = 1.8 V, k, =…

A: Given Data: VDD = 4.8 V Vtn = - Vtp = 0.5 V I1 = 2I I2 = I

Q: 4.13 For the block diagram shown in figure 4.32c: a. Reduce the blocks to canonical form b. Specify…

A: a. We need to reduce the blocks to canonical form. b. We need to specify the open-loop transfer…

Q: 4. 62

A:

Q: Reduce the Block Diagram below Simplified Block Diagram K K Vi(s) Vo(s) Vi(s) Vo(s) s(s +a) s2 + as…

A: Given

Q: 0.1 Ohm SW TIP2955 with Heat Sink 10 Amp 50 PV Bridge Rectifier 0.1 Ohm SW LM7812 with Heat Sink…

A: Full wave bridge rectifier- A circuit in which four diodes are interconnected in a bridge form in…

Q: What is the spacing criterion for a luminaires spaced with 4 meters, center to center. It’s mounting…

A: It is given that: Center to center spacing=S=4 mMounting height=MH=4 m

Q: 13) What Architecture is using by Microchip PIC Microcontroller? And briefly explain the…

A: We need to tell about the architecture used in pic , and we need to define the instruction set and…

Q: A -5 1 ΚΩ 1.5 ΚΩ 2 ΚΩ 1 ΚΩ Μ 3 ΚΩ Β ΣΚΩ ΣΚΩ C

A: Given circuit,

Q: *** *** *** . V1 9 V. . R1 -W 1.0KQ R3 W 1.0KQ *** R5 >1.0KQ **** *** R2 1,0KQ R4 -W 1,0KQ **…

A:

Q: Draw this diagram in a normal way

A: The given network is shown below,

Q: Calculate the de current (ldc) flowing through a 100 Q resistor and the power consumed by the load…

A: We have an full bridge rectifier with,  Resistance (R) = 100 ohms Supply Voltage (v) = 240 V As Vm…

Q: What is the voltage across R1 in this

A: We know that  According to Kirchoffs voltage Law(KVL) The algebraic sum of voltage across each…

Q: Explain this schematic

A: In above circuit we have connector connection with which they have connected with each other. The…

Q: u(t)=K,e(t)+ ÷Í e(t')dt" +T de(t) i 0 dt

A:

Q: Which of the following statements is true of an open component in a series circuit? a.. The circuit…

A: In question it is clearly asked in series circuit having some components. One of the series…

Q: For the network with CE unconnected, determine Rin in kn (using appropriate approximations). k 90…

A: We need to find out the input impedance for given circuit.

Q: Ptja ISI P Power too angele

A: The solution is given below

Q: Make its schematic diagram

A: According to the question, for the given breadboard connect as shown below We need to design the…

Q: R(s) 5s + 10 C(s) s4 + 2s3 + s2 + 5s + 10

A:

Q: R1 = 1.02 R3 = 1.4N E = 12V R2 = 6.7N R4 = 4.22

A:

Q: For the circuit shown, Vin is a step function that goes from 0 to VIN=1 at t=0. R=1k, C=10uF Vin 1 R…

A:

Q: RCS) Kotkos + ki S S² 1 S+3 Y(S)

A:

Q: Phasor 60 Hz powergui oltage Source 480 V Line Current u² 90.76 A 0.18+j0.24 Ohms 1483 PLoss, W 4+j3…

A: Given Data:An AC impedance circuit with,Source voltage Source impedance Load impedance To Find:The…

Q: OBJECTIVE: gain knowledge of sequential The objective of this experimen crouts. You will use tip…

A:

Q: A Moving to another question will save this response. Question 6 Elimination of armature reaction…

A: Armature reaction- It is the process in which the main magnetic field created by the magnetic field…

Q: Transformers (Ver_2) 1. A resistive load of 0.120 is connected across the secondary terminals of a…

A:

Q: Redraw the block diagram below using a consistent block size and even spacing.

A: Block diagram is redrawn in the step below,

Q: 1 kn 2 mA 2 kn 12 v(+ V. 2 kn 1 kn (1)

A: The detailed solution is attached with.

Q: Suppose the machine is initialized to its starting state '00' and then processes the input values:…

A: The given truth table is Use the truth table and the input sequences to find the next states and…

Types of Thyristors

With four layers of alternating P- and N- materials, a thyristor is a solid-state semiconductor device. It acts as a type of bi-stable switch and it conducts when the gate receives a current trigger and continues to conduct until the voltage is reverse biased across the device or by some means until the voltage is removed. The silicon-controlled rectifier is considered synonymous with thyristors by some sources. Thyristors are defined as more complex by other sources as it contains at least four-layer of alternating N-type and P-type substrate. They find large applications in the control of electrical power supplies, electric motor speed control, and ranging of light dimmers because thyristors can control large amounts of power supplies and voltage with a small device. The circuit symbol of the thyristor is given below.