ose 1 type OI statically determinate 2. Divide the chosen beam into 3 spans, pan is your own choice. 3. Load each span with 1 type of loading o ne same loading. Example. Span AB is loaded paded with a rectangular load and Span CD is 1 Iso use more than 1 concentrated load in a spa

Q: Define CMM.

A:

Q: Are both of these graphs below or above the x axis?

A: Data Given: Asked: Shear Force and Bending Moment Diagram

Q: 5.1 The recommended scales for use on technical drawings are specified in the following table.…

A: To find: Choose the suitable code for the given scales for use on technical drawings.

Q: What is the measurement benchmark

A: The given questions asks about the measurement of benchmark.

Q: When are the singularity functions used?

A: Solution-  We can observe that the shear and bending moment expressions get increasingly complicated…

Q: Define The required diameter

A: A diameter is a chord that runs through centre point of circle. The centre of circle is at midpoint…

Q: 1. The standardization of drawing guidelines that consists of eight interrelated modules is called…

A: The correct option is C.

Q: What do you mean by the slice action and how many slice operated dimensions are used?

A: #1What do you meant by the slice action?? A slice operation is defined as the particular filtration…

Q: What are the characteristics of ordinal level measurement scale variables?

A: Data provided :  Ordinal level measurement scale variables    To determine : The characteristics of…

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS & GNSS surveys.

Q: Define Closed-Form Solutions

A: Closed form solutions are obtained for the stresses and the elastic-plastic deformations when a…

Q: Define scale factor?

A: The size by which the shape is reduced is called as its scale factor. It is used when we need to…

Q: 10 25k 10'

A: The below cantilever beam is given;

Q: Explain how the symbol modes of Live and Rectangle mode, Arc and Circle mode, Dimension and…

A: Introduction:- Geographic Information systems in the area of surveying involve the development of a…

Q: Q: Define civil engineering

A: Civil engineering:

Q: What is CAD? Explain.

A: CAD-Computer-aided design is a way to  create 2D drawings and 3D models of real-world products…

Q: Quest- A column cross-section 300 mm*400 mm, 2250 mm long fixed at one end free at another end. What…

A: Effective length of the column with one end fixed and the other end free = 2*unsupported length.=…

Q: What is a scientific and a CAD diagram

A:

Q: Define oriented structure.

A: Oriented structure:

Q: Q) Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A: front view

Q: Define Minimum Dimensions

A: Brief concept introduction- Minimum Dimensions- Minimum Dimension is a very wide term and it…

Q: Defline APP.

A: Basic Concept Introduction- APP- It is the short form or abbreviation for the application.

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: How is the dimension paper used to compile an accurate Bill of Quantities??

A: Dimension paper is used in taking off which refers to the process which identifies elements of…

Q: Print scale 1:50 means that The draft is 50 times less expensive than the original A 3 cm…

A: A 3cm corresponds to half a meter

Q: i need all parts of question on the right hand corner solve I STATED FILL IN THE BLANKS.

A: Only 3 subparts can be answered at a time according to guildlines. Please resubmit the question…

Q: Define a logic loop.

A: The loop means a continuous order of formations which can repeat the work until a certain…

Q: Write a short note on:  Aligned dimensioning. Unidirectional dimensioning.

A: In this system of dimensioning, the dimensions are written along the same direction in the entire…

Q: I cannot read the equations in the answer. Is there a way to submit it in a different format?

A: Given: Flow between parallel plate with one of them moving with speed v  Required: Write the…

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 4)…

A: 1. Deactivate the voltage source (V1):Set the voltage source V1 to zero (0 V). This means the…

Q: Define the following words Tesserae Kline  Klismos Chai

A: These three terms give various elements that are important in design and art. Learning these will…

Q: Using specific examples (at least 5), discuss why you will prefer using CAD software for your…

A: A technical drawing used to convey information about an object is known as an engineering drawing. A…

Q: Please give typed answer

A: Given data:- Draw a horizontal line S60W with a length of 200m, Calculate the value of TL.

Q: Find the centroid of X and Y in tabular form.

A: A centroid is a point on the body on which the mass of a body is uniformly distributed. If the body…

Q: Can you please redo this and explain how you got what you got? I dont understand concept and show…

A: To draw a cross-section AA' and BB' for the given section.

Q: What is the importance of using Polygons?

A: A closed plane figure with multiple sides is called a polygon.

Q: Please find the centroid and Ixx for the following shapes. Show all work with neat handwriting and…

A: To help you with finding the centroid and the moment of inertia about the x-axis (Ixx) for the given…

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.