Original Schematic and OrCAD Schematic: The input primary voltage is 250V, frequency 50 Hz, primary inductance setting is 2000H and secondary inductance is 10H and voltage peak to peak ripple is approximately equal to 92mv. Ut IN gOur DIND02 DINO02 C3 Rt TXI BC54SA VOFF =0 VAMPL FREQ 50 AC0 XFRM_LINICT-SEC 02 D5 BCS4SA DIN4002 + C2 0.384m

Original Schematic and OrCAD Schematic: The input primary voltage is 250V, frequency 50 Hz, primary inductance setting is 2000H and secondary inductance is 10H and voltage peak to peak ripple is approximately equal to 92mv. Ut IN gOur DIND02 DINO02 C3 Rt TXI BC54SA VOFF =0 VAMPL FREQ 50 AC0 XFRM_LINICT-SEC 02 D5 BCS4SA DIN4002 + C2 0.384m

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4: For Figure below for sinusoidal input waveform Display and sketch the input and the output waveforms: CH1 1kO CH2 D. Vout 20V p 1N4007 f=1 kHz GND
In DC / DC switching circuits, a resistor-inductance (r-l) circuit is usually connected to the load in series, and also a reverse parallel switching diode is connected to this inductance (l). Write down your comments and approaches about the purpose for which these connected resistance, inductance and diode elements are used by an engineer's approach
Calibri (Body) -11 by AaBbCcDx AaBbCcD AaBbC AaBbCc AaB AaBbCc. mat Painter BIU 1Normal 1No Spaci. Heading 1 Heading 2 Title Subtitle Chang Styles d Font Paragraph Styles IMPEDANCE QUIZ # 2 1. What capacitance when connected in series with a 500Q resistor will limit the current drawn from a 48-mV 465-kHz source to 20µA? * a. 144pF b. 145pF c. 146pF d. 147pF MY ANSWER: c.146pF 2. What is the total impedance at 20kHz of a series circuit consisting of a 1.5mH inductance, a 100Q resistance, and a 0.08uF capacitance? * a. 1340 41.7 b. 1930 L-37.2" C. 920 290 d. 530 2-12.6°
Sketch out the fellowing signals: (a=7, b=5, c=8) a-) V = 15a(sin2r1000*ct) b-) V = 3b(cos(7500*ct)+3) c-) Assume that you measure the signal V1 using Digital Volt Meter(DVM) and ossiloscope. What will you read on the DVM display and oscilloscop dispaly when the input voltages are defined as 1-) V = 15a(sin2m1000*ct) 2-) V = 3b(cos(7500*ct)+3) Write down and sketch all the voltages for each case. Show all parameters, including period and maximum values of the signals. aR V AC aR V, aR What will you read at the DVM display when you read the voltages at AC mode What will you read at the DVM display when you read the voltages at DC range
What is the minimum size the capacitor can be if we want to keep the ripple voltage at the output to 0.5 V or less?
I am getting the output of the clamper circuit wrong, how will this circuit be output ? circuit question : Set the input voltage signal to a sinusoid with 100 Hz frequency and 20V peak-to-peak amplitude with C=1μF. Obtain and plot the input and output voltage waveforms.
İf the effective voltage value is 80 volts and the effective current value is 4A in the series RLC circuit in the figure, what is the capacitance of the capacitor?
In induction type energy meter, meter constant of energy meter is given by
just name the special diode per schematic symbol. Just give their name
In skin effect the skin depth is proportional to (f is frequency) (a) f (b) (c) (d) Vf
this is electric circuit questin ...plz solve it early .plz solve early
I need to design a power supply 110v , with an output between 6 and 9v. I did a design and I implemented a resistor after the bridge as a surge protector for the diode. I need to know if this is the right design and I need some calculations for the elements to provide an output between 6 and 9v.