or the closed-loop control system described by the block diagram shown in figure belov 1 etermine the value of K1 and K2 such that ess 17 rite the answer as K1 =,K2 = 40 R(s), K1 C(s) (s+5) K2 (0. 1s +1)

Q: it is called as the difference between the value and the measured value of a quantity a. mistakes b.…

A: In this value we will find significant figures...

Q: What is the advantage and disadvantages Static and Dynamic characteristic of measuring instruments.…

A: Step-1->Static and dynamic characteristics are two important aspects of measuring instruments.…

Q: hich of the following can’t be included in data required for coordination study? A)X/R ratio B)MVA…

A: characteristic curves of the fuses and breakers are generally analyzed in the coordination study

Q: In an electronic circuit, a. current remains the same through all the series components. b. voltage…

A: Note that,  In an electronic circuit, current remains same jn all series components and voltage…

Q: What can you say about the topic: PHILIPPINE ELECTRICAL CODE 1

A:

Q: & Prove That %3D

A: Resonance Resonance is the condition when the voltage across a circuit becomes in phase with the…

Q: 1. WRITE THE CKT. DIAGRAM OE FOUR BASIC TYPES OF SERIES CKT.

A: Series circuit A Series Circuit occurs when two or more loads are linked in series. If one load or…

Q: With neat diagram explain the construction and working of CRO.

A:

Q: In static characteristics, is defined as the difference between the true value applied to a…

A: in static characteristics, Accuracy is defined as the difference between the true value applied to a…

Q: 1.verify (Kc) and (KUL)) ?

A:

Q: Q2. What are the major carriers in the depletion region? Explain.

A: Here i have described it.

Q: Given the information appearing in Figure beside (assume Ic=IE) determine: (a) Ic. (b) VE. 18 V (c)…

A: Disclaimer:  Since you have asked multipart questions, we will solve the first three subpart for…

Q: What is HT supply?

A: What is HT supply?

Q: +V1ev1- L3 13/23 R2 v5 es V4 e4 |12/02 Figure 2060

A:

Q: IEEE and IEC standards

A: standards for electrical safetyIEC - international electrotechnical commissionIEEE - institute of…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Use electricity cost $0.08 to $0.30 in increments of $0.01. Compute a column for each type of bulb…

A:

Q: Define Analog

A: Analog can be defined as the signal, which is continuous. The analog signal has a time-varying…

Q: Identify the elements considered for the Voltage Drop calculations in D.C distribution system. O a.…

A: Inductive reactance (XL) = 2πfL  Shunt admittance (Yc)= 2πfC In dc distribution, the frequency of…

Q: The neutral current is equal to three times of ....... sequence current.

A: Current in nautral is sum of three phase currents. Current in each phase is sum of possitive…

Q: From the table, what is the circular mils for the following: a. 14 AWG a. 10 AWG b. 30 AWG c. 20 AWG

A:

Q: 19. Identify the response time of a meter. a. Time taken by output to reach final constant value…

A: Identify the response time of a meter. It's depend on the parameter.

Q: 3. Explain the successive approximation type ADC with neat schematic diagram.

A: Successive approximation ADC: The successive approximation ADC is a type of converter that converts…

Q: 3) What is the dropout ratio? What is the advantages of dropout ratio in power systems. (min 1 page)

A: A pick-up and drop-out ratio terms related to protective relays. The pickup current of a circuit…

Q: What is national electricity grid

A: In this case, we need to explain what is national electricity grid.

Q: Question : Explain the concepts of lattice matched hetero-structure. Don’t copy other works.…

A: It is asked to explain the concept of lattice matched hetero-structure.

Q: Explain the Difference between the Fundamental and Derived Unit.

A: There are generally  three types of units which are used to typically measure a particular physical…

Q: What do you understand by Safety factor, puncture and Flashover of Insulator

A: The part section of a pin type insulator is shown in  the figure below:

Q: Give the title proposal about renewable energy atleast 5 title Bachelor electrical engineering

A: Renewable Energy:- Renewable energy is produced using resources found in nature that are not…

Q: Identify the elements considered for the Voltage Drop calculations in D.C distribution system. О а.…

A: For DC distribution, voltage drop across the element?

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.