| Given i) a design speed of 70 mph, ii) 10% maximum supereleation and iii) a side friction factor of 0.10, calculate the degree of curvature (D) for the horizontal curve. 'Determine the stationing for the PC and PT of a 4.5° curve to be placed on tangents that intersect at station 175+34.75 with a deflection angle of 52°.

| Given i) a design speed of 70 mph, ii) 10% maximum supereleation and iii) a side friction factor of 0.10, calculate the degree of curvature (D) for the horizontal curve. 'Determine the stationing for the PC and PT of a 4.5° curve to be placed on tangents that intersect at station 175+34.75 with a deflection angle of 52°.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3 Horizontal curves You are asked to design a 5-degree horizontal curve with an intersection angle at the center equals 60°15'. The station of point of curvature is 155 + 26.5 ft. Calculate the following: A. Length of the curve B. Station of the point of tangency (PT) C. For first two whole stations next to PC, calculate the degree of deflection from the PC and chord length from the previous point along the horizontal curve.
XV. Reverse Curve The given reverse curve has a 60m perpendicular distance between two parallel tangents. The azimuth's tangent back creates 250 degrees while the normal tangent forms 320 degrees. If the given radius has 165m, what is the radius of the 2nd curve? 1. Compute for 11 & 12 2. Compute for T1 & T2 3. Compute for the radius of the missing value of curve.
Determine the angle of intersection.
A rising gradient AB and a falling gradient BC are to be connected by a vertical curve. Based on the data given in Table Q1, design the curve at 20 metres intervals. Table Q1 (Units are in metres) First Grade (± %) Second Grade (+ %) Sighting Distance (SSD) Driver's eye (h₁) Object height (h₂) 4.2 -1.8 145 1.05 0.3 F G RL of highest/lowest pt Chainage of highest/lowest pt| H 39.171 4048.600 K
FULL SOLUTION PLEASE. DO NOT ROUND OFF PLEASE.The common tangent BC of a reverse curve is 281 m and has an azimuth of 311 degrees . AB is tangent of the first curve whose azimuth is 250 and a distance of 320 m while CD is tangent of the second curve whose azimuth is 211 degrees and a distance of 301 m. If the radius of the second curve is 190 m, determine the following:A. radius of the first curveB. length of the curve from PC to PT
Problem 3 of A vertical parabolic summit curve has grades 2% and + 4% which intersects at station 2+020m. If the stopping sight distance is equal to 145m, compute: = a.The max. speed that a vehicle could move to avoid collision if PIEV time of the driver is 2.4 sec. and ave. skid resistance is 0.25. b.The length of the curve. c.The location (from PT), station, and elevation of the highest point in the curve if P.T. is at elevation 20.2 m amsl.
Road Engineering (Railway Engineering)
2. For the alignment shown below, give the station of the PC and PT of both curves. The station of the PI for the second curve is 100+00. The degree of curve is 6° for curve I and the deflection angle is 15°. The degree of curve is 4° for curve 2 and the deflection angle is 20°. The distance between the curves on the alignment is 200 feet. Give your answer to the appropriate level of accuracy. PISIS° k 20o PT2 20 PI2 PC1 PC2 STA 100 too
ans No. 3 only. asap
6) A horizontal curve is to be designed on a 2-lane road on a mountainous terrain. The flowingdata are known: Δ= 40 deg, T = 436.76’, station of PI: 2700+10.65, fs = 0.12, and e = 0.08.Determine the following:a) design speedb) station of the PCc) station of the PTd) deflection angle to the first 100’ statione) chord length to the first 100’ station
Correct answer urgent...m