On the attached part print, what is the diameter of the part at points "D" and "E"?

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

A:

Q: LESSON: AUTODESK AUTOCAD Choose from the choices:

A: The broken line is used to draw the large drawings which are not possible to draw on the sheet,…

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: H. What scale is used if a line 84 mm long represents a fence 63 m long?

A: Given:-  Scale length = 84 mm Actual length = 63 m = 63000 mm  To Find:-  Scale

Q: draw the orthographic view of the drawing and identify the alphabets of lines used by pointing out…

A:

Q: Figure 1. Length of line AC? Zradis 8.33" 10 5.83" 9.72" 11.33" Figure 1. Value of angle <BAC in…

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: ?What is the final reading of Vernier caliper from the figure given below 10 30 40 50 20

A: The main scale reading =5mm Vernier scale reading=0.775mm

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: 2 Constraint indicated the name and where it should be

A: Given: To find: Where the constraint should be

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object  We need to draw  The corresponding top,…

Q: Draw the front, Side and top

A: We need to draw three orthographic projection views.

Q: What is Line B?

A: Solution:

Q: In the following figure, add the largest equal coordinate tolerances so that if two parts are…

A: Maximum distance between mating hole centers, d = 0.5 mmLets assume the equal coordinate tolerance…

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: What is the precision measurement of 1 7/8 inch

A: PRECISION IS DEGREE TO WHICH REPEATED MEASUREMENTS UNDER THE SAME CONDITIONS SHOW THE SAME RESULTS.

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits…

A:

Q: What is Line J? ARROWHEAD .35mm A 7.0 В

A: Solution:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: 1. 1. Which part has the longest length? 2. 2. Which part has the smallest tolerance for the outside…

A: As this question contains multiple parts, solution is provided for first three parts as per policy.…

Q: What is Line G?

A: Solution:

Q: Using the diagram, determine the minimum diameter for DIA B, in inches. DIA A 0 000 O 00016 BASIC…

A:

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: DRAW THE ISOMETRIC FIGURES OF THE ORT

A: According to the details provided in the question, we need to draw an isometric view

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Read the following millimetric vernier caliper setting 005mm Answer with units:

A: Vernier caliper reading = reading of main scale + reading of other scale (where the two lines are…

Q: Draw the orthographic Projections of given object.

A: Orthographic projections are projections of a component in three directions that are perpendicular…

Q: Read the following inch vernier caliper setting 8. 1/128in

A: Solution:

Q: Draw the Isometric drawing of the given orthographic projections below. Use drawing scale to fit the…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.