On a 7 day wilderness expedition you'll need to heat 5.0 kg of water to the boiling point each day. The air temperature will average 25 °C. You have available canisters of compressed butane (CH₁0) fuel, which you'll burn to heat the water. Each canister has 75. g of butane in it. What is the minimum number of fuel canisters you must bring? 10, The standard heat of formation of butane at 25 °C is -125.7 kJ/mol. You'll probably find other helpful data in the ALEKS Data resource. Nathan ✔

A sample of sucrose, C12H22O11, is contaminated by sodium chloride. When the contaminated sample is burned in a bomb calorimeter, sodium chloride does not burn. What is the percentage of sucrose in the sample if a temperature increase of 1.67C is observed when 3.000 g of the sample are burned in the calorimeter? Sucrose gives off 5.64103kJ/mol when burned. The heat capacity of the calorimeter and water is 22.51 kJ/C.

A 29.1-mL sample of 1.05 M KOH is mixed with 20.9 mL of 1.07 M HBr in a coffee-cup calorimeter (see Section 6.6 of your text for a description of a coffee-cup calorimeter). The enthalpy of the reaction, written with the lowest whole-number coefficients, is 55.8 kJ. Both solutions are at 21.8C prior to mixing and reacting. What is the final temperature of the reaction mixture? When solving this problem, assume that no heat is lost from the calorimeter to the surroundings, the density of all solutions is 1.00 g/mL, and volumes are additive.

In a bomb calorimeter, the reaction vessel is surrounded by water that must be added for each experiment. Since the amount of water is not constant from experiment to experiment, the mass of water must be measured in each case. The heat capacity of the calorimeter is broken down into two parts: the water and the calorimeter components. If a calorimeter contains 1.00 kg water and has a total heat capacity of 10.84 kJ/C, what is the heat capacity of the calorimeter components?

A 50-mL solution of a dilute AgNO3 solution is added to 100 mL of a base solution in a coffee-cup calorimeter. As Ag2O(s) precipitates, the temperature of the solution increases from 23.78 C to 25.19 C. Assuming that the mixture has the same specific heat as water and a mass of 150 g, calculate the heat q. Is the precipitation reaction exothermic or endothermic?

An industrial process for manufacturing sulfuric acid, H2SO4, uses hydrogen sulfide, H2S, from the purification of natural gas. In the first step of this process, the hydrogen sulfide is burned to obtain sulfur dioxide, SO2. 2H2S(g)+3O2(g)2H2O(l)+2SO2(g);H=1124kJ The density of sulfur dioxide at 25C and 1.00 atm is 2.62 g/L, and the molar heat capacity is 30.2 J/(mol C). (a) How much heat would be evolved in producing 1.00 L of SO2 at 25C and 1.00 atm? (b) Suppose heat from this reaction is used to heat 1.00 L of the SO2 from 25C to 500C for its use in the next step of the process. What percentage of the heat evolved is required for this?

Nitric acid, HNO3, can be prepared by the following sequence of reactions: 4NH3(g)+5O2(g)4NO(g)+6H2O(g)2NO(g)+O2(g)2NO2(g)3NO2(g)+H2O(l)2HNO3(l)+NO(g) How much heat is evolved when 1 mol of NH3(g) is converted to HNO3(l)? Assume standard states at 25 C.

The equation for the combustion of butane, C4H10, is C4H10(g)+132O2(g)4CO2(g)+5H2O(g) Which one of the following generates the least heat? Why? a Burning one mole of butane b Reacting one mole of oxygen with excess butane c Producing one mole of carbon dioxide by burning butane d Producing one mole of water by burning butane

In a coffee-cup calorimeter, 150.0 mL of 0.50 M HCI is added to 50.0 mL of 1.00 M NaOH to make 200.0 g solution at an initial temperature of 48.2C. If the enthalpy of neutralization for the reaction between a strong acid and a strong base is 56 kJ/mol, calculate the final temperature of the calorimeter contents. Assume the specific heat capacity of the solution is 4.184 J/g C and assume no heat Joss to the surroundings.

9.104 An engineer is using sodium metal as a cooling agent in a design because it has useful thermal properties. Looting up the heat capacity, the engineer finds a value of 28.2 J mol-l °C-l. Carelessly, he wrote this number down without units. As a result, it was later taken as specific heat. (a) What would he the difference between these two values? (b) Would the engineer overestimate the ability of sodium to remove heat from the system or underestimate it because of this error? Be sure to explain your reasoning.