An equilateral triangular truss ABC has a vertical member AC that has one of its side 2m long. It hasa roller support at A and hinged at C. The truss carries a vertical load of 50 kN at joint B. Cross-sectional area of all members is 800 mm? and E=200,000 MPa. Determine the force carried bymember BC due to the 50kN applied load.2m602m60OB50 kN602mSelect one:O a. 35 kNO b. 45 kNO c. 25 kNO d. 50 kN

oller support at A and hinged at C. The truss carries a vertical load of 50 kN at je ctional area of all members is 800 mm? and E=200,000 MPa. Determine the ford ember BC due to the 50KN applied load. 2m 60 2m 60° so kN 60 2m ene: =5 IN 5 kN 5 kN S0 kN

oller support at A and hinged at C. The truss carries a vertical load of 50 kN at je ctional area of all members is 800 mm? and E=200,000 MPa. Determine the ford ember BC due to the 50KN applied load. 2m 60 2m 60° so kN 60 2m ene: =5 IN 5 kN 5 kN S0 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The truss shown is supported by a pin at A and a roller at F. Two force are applied to the truss. The force at C in directly above F., All the truss members are 3m long making equilateral triangles. Detemine the force in member CD. The answers have units of kilonewtons. 5 kN 3 kN BE
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E seel = 200 Gpa and a= 1.5 m, b= Im, d=30 mm, h= 8 mm 2a
Determine the forces in members CG and GH of the symmetrically loaded truss. The forces are positive if in tension and negative if in compression. B 5 m A 77 Answers: CG= i GH = i -5 m 30° 5 m H -6 m L eTextbook and Media G L D -5 m L L L 2 E
= The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 3 ft (O с A 5 ft O B 6 ft D 2750 lb 3.75 in 3.75 in 0 in 0.80 Strut AB Beam CD (b Xh) Bolt (dmin) -0.50 in
3.75 نقطة )نقاط( السؤال 5 The beam is supported by a pin at A and a short link BC. If P = 5 kN and the diameter of the pin at C is 8 mm, determine the factor of safety against shear stress of pin .C assuming 800 MPa 2P |0.5,m 1 m-1.5 m -1.5 m- 4P 4P P. 0.5 m| 30 B 1.269 1.257 1.322 O 1.462 O
If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm 2а b a - a
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
If the maximum allowable force (tensile or compressive) in members GF in the pin-connected truss shown is known to be 270 kN. Determine the maximum load P that can be applied to the truss. 6 m 6 m 6m 6m 6m Select one: OA.P= 90.00 KN OB. P = 270.00 KN OC.P = 405.00 KN OD.P = 180.00 KN OE.P = 135.00 KN P.
- Determine the force in member GH and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FGH = Submit Part B. FBC= μA Value Part C Request Answer Determine the force in member BC and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA Value Submit Request Answer 3 μA Units FBG = Value → Units ? Determine the force in member BG and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units ? ?