Determine the external reactions at A and F for the roof truss loaded as shown (positive answers are to the right and up). The vert loads represent the effect of the supported roofing materials, while the 300-N force represents a wind load. 300 N y 250 N A Answers: Ax Ay = Fv= 60° Mo B i 550 N 60⁰ 30° 480 N 540 N 30° G -16.5 m- E 30° Z Z N N N 240 N x

Determine the external reactions at A and F for the roof truss loaded as shown (positive answers are to the right and up). The vert loads represent the effect of the supported roofing materials, while the 300-N force represents a wind load. 300 N y 250 N A Answers: Ax Ay = Fv= 60° Mo B i 550 N 60⁰ 30° 480 N 540 N 30° G -16.5 m- E 30° Z Z N N N 240 N x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the largest weight W that can be supported by the two wires AB and AC. The working stresses are 14.5 ksi for AB and 21.8 ksi for AC. The cross-sectional areas of AB and AC are 0.6 squares inches and 0.3 squares inches respectively. 30° A 45° W B.
Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F = 4.6 kN, a = 4.0 m, b = 3 m, c = 2 m, and d = 2 m. A F Answers: BE= BD = a i i B b E a b D с d KN KN
If the allowable bearing stress for the material under the supports at A and B is = 710 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 650 lb/ft, a = 10ft, and b = 5 ft. Answer: Pmax i a B b lb
a=7m b=2m c=5m 2 3rd QUESTION Determine the reaction forces force of the loaded truss. 45° 10 kN C b B a
Determine the forces in members CG and GH of the symmetrically loaded truss. The forces are positive if in tension and negative if in compression. B 5 m A 77 Answers: CG= i GH = i -5 m 30° 5 m H -6 m L eTextbook and Media G L D -5 m L L L 2 E
Which of the following is the nearest value for the force at member BC? a. 5kN tension b. 1.6 kN tension c. 1.6 kN compression d. 5 kN compression
If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
A simply supported wood beam that is 14.1 m long carries a 47 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 360 mm, a = 70 mm, andc = 20 mm. Section a-a is located at x = 2.4 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. y H a a A В K L 2L Answer: (a) TH = i kPa (b) TK = i КРа (c) Tmax = i kPa (d) Omax MPa i 13
h.w 2 Problems: 1. The cantilever truss in Figure is hinged at D and E. Find the force in each member. 1000 N Answer: FAB 2000 N tension FAC 1732.05 N compression FBC=866.02 N compression FBD = 2500 N tension Fco 2020.72 N tension FCE 3175.42 N compression
3
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F