Oil, with S.G.= 0. 6, flows on a pipe, with center m as shown in Figure 4. Attached on this pipe is a piezometer at point A and tubes for open type manometers at both points B and C. At the end of the tube attached to point B is a fluid, called Fluid Y, which has a height hz and a specific gravity of S.G. = 1.497. At the end of the tube attached to point C is a fluid, called Fluid X, which has a height h, and a specific gravity of S.G. 13.6. How much greater is the height of fluid Y than that of fluid X? Express this relationship in percent (%). 人F Y h2 A m

Oil, with S.G.= 0. 6, flows on a pipe, with center m as shown in Figure 4. Attached on this pipe is a piezometer at point A and tubes for open type manometers at both points B and C. At the end of the tube attached to point B is a fluid, called Fluid Y, which has a height hz and a specific gravity of S.G. = 1.497. At the end of the tube attached to point C is a fluid, called Fluid X, which has a height h, and a specific gravity of S.G. 13.6. How much greater is the height of fluid Y than that of fluid X? Express this relationship in percent (%). 人F Y h2 A m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A U-tube manometer is arranged, as shown in Fig. 2.15, to measure the pressure difference between two points A and B in a pipeline conveying water of density 1000 kg/m³. The density of the manometric liquid Q is 13600 kg/m³ and point B is 0.3 m higher than point A. Calculate the pressure difference when h = 0.7 m. T Manometric liquid Q of density Pman Figure 2.15 Measurement of pressure difference Fluid P, of density blup all to 20 lens
A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A U-tube manometer is connected to the pipe through pressure taps located 4 in. on either side of the device. The gage fluid in the manometer has a specific weight of 112 lb/ft³. Determine the differential reading of the manometer corresponding to a pressure drop between the taps of 0.7 lb/in². h = ft
I need the answer as soon as possible
I need all right solutions with clear calculations
I need the answer as soon as possible
A Prandtl tube (Pitot-static tube with C = 1) is used to measure the velocity of water. The differential manometer reading is 10 mm of liquid column with a relative density of 10. Assuming g = 9.8 m/s2, the velocity of water (in m/s) is -
Please don't copy ,I need right solution.
Q2) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure tap at station 1. The velocity at station 2 is 4 times that at station 1. Air with a density of 1.2 kg/m3 flows through the duct. A water manometer is connected between the stagnation probe and the pressure tap, and a deflection of Ah = 13.7 cm is measured. What is the velocity at Vertical station 2? Water
E9
(Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the pipe contraction shown in the figure below. The flowing fluid is water, and viscous effects are negligible. Determine the two manometer readings, h and H. V=2.2 ft/s h= H= 6.3 in. Air SG= 1.10 ft •ft H 3.5 in. h
In the inclined manometer shown in the figure below, the reservoir is large. Its surface may be assumed to remain at a fixed elevation. A is connected to a gas pipeline and the deflection noted on the inclined glass tube is 100 mm. Assuming q = 30° and the manometric fluid as oil with specific gravity of 0.86, the pressure at A is A 100 mm Ꮎ B
Q.23 Consider the flow of water through the frictionless pipe as shown in the figure. There is a sudden expansion at a section in the pipe. The flow velocity is 2.5 m/s and 1 m/s in AB and BC portion of the pipe respectively. The reading '' of the mercury- water differential manometer is: [Take specific gravity of mercury as 13.6] A O 50 cm Q B ↓ Water }